1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
|
# Copyright (c) 2016 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/performance.robot
| Library | resources.libraries.python.topology.Topology
| Library | resources.libraries.python.NodePath
| Library | resources.libraries.python.InterfaceUtil
| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']} | WITH NAME | dut1_v4
| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']} | WITH NAME | dut2_v4
| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_SHORT
| ... | NIC_Intel-X520-DA2
| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
| ... | L3 | Intel-X520-DA2
| Suite Teardown | 3-node Performance Suite Teardown
| Test Setup | Setup all DUTs before test
| Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs
| Documentation | *Reference NDR throughput IPv4 routing verify test cases*
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
| ... | with single links between nodes.
| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
| ... | routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with
| ... | 2p10GE NIC X520 Niantic by Intel.
| ... | *[Ver] TG verification:* In short performance tests, TG verifies
| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet
| ... | loss tolerance. Ref-NDR value is periodically updated acording to
| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long
| ... | performance tests for the same DUT confiiguration. Test packets are
| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with
| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61
| ... | and generated payload.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Test Cases ***
| TC01: Verify 64B ref-NDR at 2x 3.5Mpps - DUT IPv4 - 1thread 1core 1rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
| | ${framesize}= | Set Variable | 64
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 3.5mpps
| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 - 1thread 1core 1rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
| | ${framesize}= | Set Variable | 1518
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 812743pps
| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
| TC03: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 - 1thread 1core 1rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \
| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
| | ${framesize}= | Set Variable | 9000
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 138580pps
| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
| TC04: Verify 64B ref-NDR at 2x 7.5Mpps - DUT IPv4 - 2threads, 2cores, 1rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 64
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 7.5mpps
| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 - 2threads, 2cores, 1rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 1518
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 812743pps
| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 - 2threads, 2cores, 1rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \
| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 9000
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 138580pps
| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
| TC07: Verify 64B ref-NDR at 2x 10.0Mpps - DUT IPv4 - 4threads, 4cores, 2rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 64
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 10.0mpps
| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 - 4threads, 4cores, 2rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 1518
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 812743pps
| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Add No Multi Seg to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 - 4threads, 4cores, 2rxq
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \
| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte
| | ... | frames using single trial throughput test.
| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
| | ${framesize}= | Set Variable | 9000
| | ${duration}= | Set Variable | 10
| | ${rate}= | Set Variable | 138580pps
| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
| | And Add all PCI devices to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | And IPv4 forwarding initialized in a 3-node circular topology
| | Then Traffic should pass with no loss | ${duration} | ${rate}
| | ... | ${framesize} | 3-node-IPv4
|