blob: b5ff0b6c563e345297e5408865b4a19a95e15b93 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
|
# Copyright (c) 2019 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/performance/performance_setup.robot
| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot
| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
| ...
| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | IP4FWD | ENCAP | LISP | IP4UNRLAY | IP4OVRLAY
| ...
| Suite Setup | Set up 3-node performance topology with DUT's NIC model
| ... | L3 | ${nic_name}
| Suite Teardown | Tear down 3-node performance topology
| ...
| Test Setup | Set up performance test
| Test Teardown | Tear down performance test
| ...
| Test Template | Local Template
| ...
| Documentation | *RFC2544: Pkt throughput Lisp test cases*
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4 on DUT1-DUT2,\
| ... | Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and static routes. LISPoIPv4 tunnel is configured between DUT1\
| ... | and DUT2. DUT1 and DUT2 tested with ${nic_name}.\
| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
| ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\
| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
| ... | of packets transmitted. NDR and PDR are discovered for different\
| ... | Ethernet L2 frame sizes using MLRsearch library.\
| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
| ... | flow-group) with all packets containing Ethernet header, IPv4 header
| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
| ... | addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC6830.
*** Variables ***
| ${nic_name}= | Intel-X710
| ${overhead}= | ${8}
# Traffic profile:
| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
*** Keywords ***
| Local Template
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters\
| | ... | config.
| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
| | ...
| | ... | *Arguments:*
| | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1).
| | ... | Type: integer, string
| | ... | - phy_cores - Number of physical cores. Type: integer
| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
| | ...
| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
| | ...
| | Set Test Variable | \${frame_size}
| | ...
| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
| | And Add PCI devices to all DUTs
| | Set Max Rate And Jumbo And Handle Multi Seg
| | And Apply startup configuration on all VPP DUTs
| | When Initialize LISP IPv4 forwarding in 3-node circular topology
| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
| | ... | ${dut2_to_tg_ip4} | ${prefix4}
| | And Configure LISP topology in 3-node circular topology
| | ... | ${dut1} | ${dut1_if2} | ${NONE}
| | ... | ${dut2} | ${dut2_if1} | ${NONE}
| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
| | Then Find NDR and PDR intervals using optimized search
*** Test Cases ***
| tc01-64B-1c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 64B | 1C
| | frame_size=${64} | phy_cores=${1}
| tc02-64B-2c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 64B | 2C
| | frame_size=${64} | phy_cores=${2}
| tc03-64B-4c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 64B | 4C
| | frame_size=${64} | phy_cores=${4}
| tc04-1518B-1c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 1518B | 1C
| | frame_size=${1518} | phy_cores=${1}
| tc05-1518B-2c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 1518B | 2C
| | frame_size=${1518} | phy_cores=${2}
| tc06-1518B-4c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 1518B | 4C
| | frame_size=${1518} | phy_cores=${4}
| tc07-9000B-1c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 9000B | 1C
| | frame_size=${9000} | phy_cores=${1}
| tc08-9000B-2c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 9000B | 2C
| | frame_size=${9000} | phy_cores=${2}
| tc09-9000B-4c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | 9000B | 4C
| | frame_size=${9000} | phy_cores=${4}
| tc10-IMIX-1c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | IMIX | 1C
| | frame_size=IMIX_v4_1 | phy_cores=${1}
| tc11-IMIX-2c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | IMIX | 2C
| | frame_size=IMIX_v4_1 | phy_cores=${2}
| tc12-IMIX-4c-ethip4lispip4-ip4base-ndrpdr
| | [Tags] | IMIX | 4C
| | frame_size=IMIX_v4_1 | phy_cores=${4}
|
