1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
|
.. SPDX-License-Identifier: BSD-3-Clause
Copyright(c) 2015 Intel Corporation.
RX/TX Callbacks Sample Application
==================================
The RX/TX Callbacks sample application is a packet forwarding application that
demonstrates the use of user defined callbacks on received and transmitted
packets. The application performs a simple latency check, using callbacks, to
determine the time packets spend within the application.
In the sample application a user defined callback is applied to all received
packets to add a timestamp. A separate callback is applied to all packets
prior to transmission to calculate the elapsed time, in CPU cycles.
Compiling the Application
-------------------------
To compile the sample application see :doc:`compiling`.
The application is located in the ``rxtx_callbacks`` sub-directory.
The callbacks feature requires that the ``CONFIG_RTE_ETHDEV_RXTX_CALLBACKS``
setting is on in the ``config/common_`` config file that applies to the
target. This is generally on by default:
.. code-block:: console
CONFIG_RTE_ETHDEV_RXTX_CALLBACKS=y
Running the Application
-----------------------
To run the example in a ``linuxapp`` environment:
.. code-block:: console
./build/rxtx_callbacks -l 1 -n 4
Refer to *DPDK Getting Started Guide* for general information on running
applications and the Environment Abstraction Layer (EAL) options.
Explanation
-----------
The ``rxtx_callbacks`` application is mainly a simple forwarding application
based on the :doc:`skeleton`. See that section of the documentation for more
details of the forwarding part of the application.
The sections below explain the additional RX/TX callback code.
The Main Function
~~~~~~~~~~~~~~~~~
The ``main()`` function performs the application initialization and calls the
execution threads for each lcore. This function is effectively identical to
the ``main()`` function explained in :doc:`skeleton`.
The ``lcore_main()`` function is also identical.
The main difference is in the user defined ``port_init()`` function where the
callbacks are added. This is explained in the next section:
The Port Initialization Function
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The main functional part of the port initialization is shown below with
comments:
.. code-block:: c
static inline int
port_init(uint16_t port, struct rte_mempool *mbuf_pool)
{
struct rte_eth_conf port_conf = port_conf_default;
const uint16_t rx_rings = 1, tx_rings = 1;
struct ether_addr addr;
int retval;
uint16_t q;
if (port >= rte_eth_dev_count())
return -1;
/* Configure the Ethernet device. */
retval = rte_eth_dev_configure(port, rx_rings, tx_rings, &port_conf);
if (retval != 0)
return retval;
/* Allocate and set up 1 RX queue per Ethernet port. */
for (q = 0; q < rx_rings; q++) {
retval = rte_eth_rx_queue_setup(port, q, RX_RING_SIZE,
rte_eth_dev_socket_id(port), NULL, mbuf_pool);
if (retval < 0)
return retval;
}
/* Allocate and set up 1 TX queue per Ethernet port. */
for (q = 0; q < tx_rings; q++) {
retval = rte_eth_tx_queue_setup(port, q, TX_RING_SIZE,
rte_eth_dev_socket_id(port), NULL);
if (retval < 0)
return retval;
}
/* Start the Ethernet port. */
retval = rte_eth_dev_start(port);
if (retval < 0)
return retval;
/* Enable RX in promiscuous mode for the Ethernet device. */
rte_eth_promiscuous_enable(port);
/* Add the callbacks for RX and TX.*/
rte_eth_add_rx_callback(port, 0, add_timestamps, NULL);
rte_eth_add_tx_callback(port, 0, calc_latency, NULL);
return 0;
}
The RX and TX callbacks are added to the ports/queues as function pointers:
.. code-block:: c
rte_eth_add_rx_callback(port, 0, add_timestamps, NULL);
rte_eth_add_tx_callback(port, 0, calc_latency, NULL);
More than one callback can be added and additional information can be passed
to callback function pointers as a ``void*``. In the examples above ``NULL``
is used.
The ``add_timestamps()`` and ``calc_latency()`` functions are explained below.
The add_timestamps() Callback
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The ``add_timestamps()`` callback is added to the RX port and is applied to
all packets received:
.. code-block:: c
static uint16_t
add_timestamps(uint16_t port __rte_unused, uint16_t qidx __rte_unused,
struct rte_mbuf **pkts, uint16_t nb_pkts, void *_ __rte_unused)
{
unsigned i;
uint64_t now = rte_rdtsc();
for (i = 0; i < nb_pkts; i++)
pkts[i]->udata64 = now;
return nb_pkts;
}
The DPDK function ``rte_rdtsc()`` is used to add a cycle count timestamp to
each packet (see the *cycles* section of the *DPDK API Documentation* for
details).
The calc_latency() Callback
~~~~~~~~~~~~~~~~~~~~~~~~~~~
The ``calc_latency()`` callback is added to the TX port and is applied to all
packets prior to transmission:
.. code-block:: c
static uint16_t
calc_latency(uint16_t port __rte_unused, uint16_t qidx __rte_unused,
struct rte_mbuf **pkts, uint16_t nb_pkts, void *_ __rte_unused)
{
uint64_t cycles = 0;
uint64_t now = rte_rdtsc();
unsigned i;
for (i = 0; i < nb_pkts; i++)
cycles += now - pkts[i]->udata64;
latency_numbers.total_cycles += cycles;
latency_numbers.total_pkts += nb_pkts;
if (latency_numbers.total_pkts > (100 * 1000 * 1000ULL)) {
printf("Latency = %"PRIu64" cycles\n",
latency_numbers.total_cycles / latency_numbers.total_pkts);
latency_numbers.total_cycles = latency_numbers.total_pkts = 0;
}
return nb_pkts;
}
The ``calc_latency()`` function accumulates the total number of packets and
the total number of cycles used. Once more than 100 million packets have been
transmitted the average cycle count per packet is printed out and the counters
are reset.
|
