diff options
author | Mauro Sardara <msardara@cisco.com> | 2019-09-23 19:34:23 +0200 |
---|---|---|
committer | Mauro Sardara <msardara@cisco.com> | 2019-09-24 11:14:16 +0200 |
commit | a0da41b243661a039481d2c254d7db8f55f18d2b (patch) | |
tree | e06e06a609588ceb8f5e293abc02a4a02da39d4d /extras/hicn-extra-plugin/README.md | |
parent | d6bd901a818e10f2e224bfaaaf20b39b60b6009f (diff) |
[HICN-279] Added libmemif packaging.
Change-Id: Ie8662059163b7a01211bb18fb8f6b77bbbc07279
Signed-off-by: Mauro Sardara <msardara@cisco.com>
Diffstat (limited to 'extras/hicn-extra-plugin/README.md')
-rw-r--r-- | extras/hicn-extra-plugin/README.md | 49 |
1 files changed, 49 insertions, 0 deletions
diff --git a/extras/hicn-extra-plugin/README.md b/extras/hicn-extra-plugin/README.md new file mode 100644 index 000000000..40363ef18 --- /dev/null +++ b/extras/hicn-extra-plugin/README.md @@ -0,0 +1,49 @@ +# Configure VPP and FRRouting for OSPF6 +This document describes how to configure the VPP with hicn_router plugin and FRR to enable the OSPF protocol. The VPP and FRR +are configured in a docker file. + +## DPDK configuration on host machine: + +- Install and configure dpdk + - make install T=x86_64-native-linux-gcc && cd x86_64-native-linux-gcc && sudo make install + - modprobe uio + - modprobe uio_pci_generic + - dpdk-devbind --status + - the PCIe number of the desired device can be observed ("xxx") + - sudo dpdk-devbind -b uio_pci_generic "xxx" +## VPP configuration: + +- Run and configure the VPP (hICN router plugin is required to be installed in VPP) + - set int state TenGigabitEtherneta/0/0 up + - set int ip address TenGigabitEtherneta/0/0 a001::1/24 + - create loopback interface + - set interface state loop0 up + - set interface ip address loop0 b001::1/128 + - enable tap-inject # This creates the taps by router plugin + - show tap-inject # This shows the created taps + - ip mroute add ff02::/64 via local Forward # ff02:: is multicast ip address + - ip mroute add ff02::/64 via TenGigabitEtherneta/0/0 Accept + - ip mroute add ff02::/64 via loop0 Accept + +- Setup the tap interface + - ip addr add a001::1/24 dev vpp0 + - ip addr add b001::1/128 dev vpp1 + - ip link set dev vpp0 up + - ip link set dev vpp1 up + +## FRR configuration: + +- Run and configure FRRouting (ospf) + - /usr/lib/frr/frrinit.sh start & + - vtysh + - configure terminal + - router ospf6 + - area 0.0.0.0 range a001::1/24 + - area 0.0.0.0 range b001::1/128 + - interface vpp0 area 0.0.0.0 + - interface vpp1 area 0.0.0.0 + - end + - wr + - add "no ipv6 nd suppress-ra" to the first configurtion part of the /etc/frr/frr.conf +After the following configuration, the traffic over tap interface can be observered through "tcpdump- i vpp1". +The neighborhood and route can be seen by the "show ipv6 ospf6 neighbor/route". |