diff options
author | Mauro Sardara <msardara@cisco.com> | 2019-12-06 18:25:28 +0100 |
---|---|---|
committer | Mauro Sardara <msardara@cisco.com> | 2019-12-10 17:50:49 +0100 |
commit | 3f21100e1d2ec47b64670a8b08d0c9d067bf9ef3 (patch) | |
tree | 6774ce7f2bc020b646366503eaa6acf2f0af13eb /extras/hicn-extra-plugin/README.md | |
parent | e8eda2c819b36555d9d6b080eaf8b4b1109d7646 (diff) |
[HICN-430] Rework on CMake
Change way targets are defined: each project defines targets.
Fix project BUILD flags
Add build-extras bash script
Rework build tree of extras folder, using ExternalProject_Add
Change-Id: I82fa29896e54c8a033490eba013c3f0431bec9d0
Signed-off-by: Mauro Sardara <msardara@cisco.com>
Diffstat (limited to 'extras/hicn-extra-plugin/README.md')
-rw-r--r-- | extras/hicn-extra-plugin/README.md | 49 |
1 files changed, 0 insertions, 49 deletions
diff --git a/extras/hicn-extra-plugin/README.md b/extras/hicn-extra-plugin/README.md deleted file mode 100644 index 40363ef18..000000000 --- a/extras/hicn-extra-plugin/README.md +++ /dev/null @@ -1,49 +0,0 @@ -# Configure VPP and FRRouting for OSPF6 -This document describes how to configure the VPP with hicn_router plugin and FRR to enable the OSPF protocol. The VPP and FRR -are configured in a docker file. - -## DPDK configuration on host machine: - -- Install and configure dpdk - - make install T=x86_64-native-linux-gcc && cd x86_64-native-linux-gcc && sudo make install - - modprobe uio - - modprobe uio_pci_generic - - dpdk-devbind --status - - the PCIe number of the desired device can be observed ("xxx") - - sudo dpdk-devbind -b uio_pci_generic "xxx" -## VPP configuration: - -- Run and configure the VPP (hICN router plugin is required to be installed in VPP) - - set int state TenGigabitEtherneta/0/0 up - - set int ip address TenGigabitEtherneta/0/0 a001::1/24 - - create loopback interface - - set interface state loop0 up - - set interface ip address loop0 b001::1/128 - - enable tap-inject # This creates the taps by router plugin - - show tap-inject # This shows the created taps - - ip mroute add ff02::/64 via local Forward # ff02:: is multicast ip address - - ip mroute add ff02::/64 via TenGigabitEtherneta/0/0 Accept - - ip mroute add ff02::/64 via loop0 Accept - -- Setup the tap interface - - ip addr add a001::1/24 dev vpp0 - - ip addr add b001::1/128 dev vpp1 - - ip link set dev vpp0 up - - ip link set dev vpp1 up - -## FRR configuration: - -- Run and configure FRRouting (ospf) - - /usr/lib/frr/frrinit.sh start & - - vtysh - - configure terminal - - router ospf6 - - area 0.0.0.0 range a001::1/24 - - area 0.0.0.0 range b001::1/128 - - interface vpp0 area 0.0.0.0 - - interface vpp1 area 0.0.0.0 - - end - - wr - - add "no ipv6 nd suppress-ra" to the first configurtion part of the /etc/frr/frr.conf -After the following configuration, the traffic over tap interface can be observered through "tcpdump- i vpp1". -The neighborhood and route can be seen by the "show ipv6 ospf6 neighbor/route". |