diff options
Diffstat (limited to 'src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_phy.h')
| -rwxr-xr-x | src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_phy.h | 256 |
1 files changed, 0 insertions, 256 deletions
diff --git a/src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_phy.h b/src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_phy.h deleted file mode 100755 index 5387c5e7..00000000 --- a/src/dpdk_lib18/librte_eal/linuxapp/kni/ethtool/igb/e1000_phy.h +++ /dev/null @@ -1,256 +0,0 @@ -/******************************************************************************* - - Intel(R) Gigabit Ethernet Linux driver - Copyright(c) 2007-2013 Intel Corporation. - - This program is free software; you can redistribute it and/or modify it - under the terms and conditions of the GNU General Public License, - version 2, as published by the Free Software Foundation. - - This program is distributed in the hope it will be useful, but WITHOUT - ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or - FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for - more details. - - You should have received a copy of the GNU General Public License along with - this program; if not, write to the Free Software Foundation, Inc., - 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. - - The full GNU General Public License is included in this distribution in - the file called "COPYING". - - Contact Information: - e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> - Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 - -*******************************************************************************/ - -#ifndef _E1000_PHY_H_ -#define _E1000_PHY_H_ - -void e1000_init_phy_ops_generic(struct e1000_hw *hw); -s32 e1000_null_read_reg(struct e1000_hw *hw, u32 offset, u16 *data); -void e1000_null_phy_generic(struct e1000_hw *hw); -s32 e1000_null_lplu_state(struct e1000_hw *hw, bool active); -s32 e1000_null_write_reg(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_null_set_page(struct e1000_hw *hw, u16 data); -s32 e1000_read_i2c_byte_null(struct e1000_hw *hw, u8 byte_offset, - u8 dev_addr, u8 *data); -s32 e1000_write_i2c_byte_null(struct e1000_hw *hw, u8 byte_offset, - u8 dev_addr, u8 data); -s32 e1000_check_downshift_generic(struct e1000_hw *hw); -s32 e1000_check_polarity_m88(struct e1000_hw *hw); -s32 e1000_check_polarity_igp(struct e1000_hw *hw); -s32 e1000_check_polarity_ife(struct e1000_hw *hw); -s32 e1000_check_reset_block_generic(struct e1000_hw *hw); -s32 e1000_copper_link_setup_igp(struct e1000_hw *hw); -s32 e1000_copper_link_setup_m88(struct e1000_hw *hw); -s32 e1000_copper_link_setup_m88_gen2(struct e1000_hw *hw); -s32 e1000_phy_force_speed_duplex_igp(struct e1000_hw *hw); -s32 e1000_phy_force_speed_duplex_m88(struct e1000_hw *hw); -s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw); -s32 e1000_get_cable_length_m88(struct e1000_hw *hw); -s32 e1000_get_cable_length_m88_gen2(struct e1000_hw *hw); -s32 e1000_get_cable_length_igp_2(struct e1000_hw *hw); -s32 e1000_get_cfg_done_generic(struct e1000_hw *hw); -s32 e1000_get_phy_id(struct e1000_hw *hw); -s32 e1000_get_phy_info_igp(struct e1000_hw *hw); -s32 e1000_get_phy_info_m88(struct e1000_hw *hw); -s32 e1000_get_phy_info_ife(struct e1000_hw *hw); -s32 e1000_phy_sw_reset_generic(struct e1000_hw *hw); -void e1000_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl); -s32 e1000_phy_hw_reset_generic(struct e1000_hw *hw); -s32 e1000_phy_reset_dsp_generic(struct e1000_hw *hw); -s32 e1000_read_kmrn_reg_generic(struct e1000_hw *hw, u32 offset, u16 *data); -s32 e1000_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data); -s32 e1000_set_page_igp(struct e1000_hw *hw, u16 page); -s32 e1000_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data); -s32 e1000_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data); -s32 e1000_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data); -s32 e1000_set_d3_lplu_state_generic(struct e1000_hw *hw, bool active); -s32 e1000_setup_copper_link_generic(struct e1000_hw *hw); -s32 e1000_write_kmrn_reg_generic(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_phy_has_link_generic(struct e1000_hw *hw, u32 iterations, - u32 usec_interval, bool *success); -s32 e1000_phy_init_script_igp3(struct e1000_hw *hw); -enum e1000_phy_type e1000_get_phy_type_from_id(u32 phy_id); -s32 e1000_determine_phy_address(struct e1000_hw *hw); -s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg); -s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg); -void e1000_power_up_phy_copper(struct e1000_hw *hw); -void e1000_power_down_phy_copper(struct e1000_hw *hw); -s32 e1000_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data); -s32 e1000_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data); -s32 e1000_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data); -s32 e1000_write_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 data); -s32 e1000_copper_link_setup_82577(struct e1000_hw *hw); -s32 e1000_check_polarity_82577(struct e1000_hw *hw); -s32 e1000_get_phy_info_82577(struct e1000_hw *hw); -s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw); -s32 e1000_get_cable_length_82577(struct e1000_hw *hw); -s32 e1000_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data); -s32 e1000_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data); -s32 e1000_read_phy_reg_mphy(struct e1000_hw *hw, u32 address, u32 *data); -s32 e1000_write_phy_reg_mphy(struct e1000_hw *hw, u32 address, u32 data, - bool line_override); -bool e1000_is_mphy_ready(struct e1000_hw *hw); - -#define E1000_MAX_PHY_ADDR 8 - -/* IGP01E1000 Specific Registers */ -#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */ -#define IGP01E1000_PHY_PORT_STATUS 0x11 /* Status */ -#define IGP01E1000_PHY_PORT_CTRL 0x12 /* Control */ -#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health */ -#define IGP02E1000_PHY_POWER_MGMT 0x19 /* Power Management */ -#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* Page Select */ -#define BM_PHY_PAGE_SELECT 22 /* Page Select for BM */ -#define IGP_PAGE_SHIFT 5 -#define PHY_REG_MASK 0x1F - -/* GS40G - I210 PHY defines */ -#define GS40G_PAGE_SELECT 0x16 -#define GS40G_PAGE_SHIFT 16 -#define GS40G_OFFSET_MASK 0xFFFF -#define GS40G_PAGE_2 0x20000 -#define GS40G_MAC_REG2 0x15 -#define GS40G_MAC_LB 0x4140 -#define GS40G_MAC_SPEED_1G 0X0006 -#define GS40G_COPPER_SPEC 0x0010 -#define GS40G_CS_POWER_DOWN 0x0002 - -#define HV_INTC_FC_PAGE_START 768 -#define I82578_ADDR_REG 29 -#define I82577_ADDR_REG 16 -#define I82577_CFG_REG 22 -#define I82577_CFG_ASSERT_CRS_ON_TX (1 << 15) -#define I82577_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift */ -#define I82577_CTRL_REG 23 - -/* 82577 specific PHY registers */ -#define I82577_PHY_CTRL_2 18 -#define I82577_PHY_LBK_CTRL 19 -#define I82577_PHY_STATUS_2 26 -#define I82577_PHY_DIAG_STATUS 31 - -/* I82577 PHY Status 2 */ -#define I82577_PHY_STATUS2_REV_POLARITY 0x0400 -#define I82577_PHY_STATUS2_MDIX 0x0800 -#define I82577_PHY_STATUS2_SPEED_MASK 0x0300 -#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200 - -/* I82577 PHY Control 2 */ -#define I82577_PHY_CTRL2_MANUAL_MDIX 0x0200 -#define I82577_PHY_CTRL2_AUTO_MDI_MDIX 0x0400 -#define I82577_PHY_CTRL2_MDIX_CFG_MASK 0x0600 - -/* I82577 PHY Diagnostics Status */ -#define I82577_DSTATUS_CABLE_LENGTH 0x03FC -#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2 - -/* 82580 PHY Power Management */ -#define E1000_82580_PHY_POWER_MGMT 0xE14 -#define E1000_82580_PM_SPD 0x0001 /* Smart Power Down */ -#define E1000_82580_PM_D0_LPLU 0x0002 /* For D0a states */ -#define E1000_82580_PM_D3_LPLU 0x0004 /* For all other states */ -#define E1000_82580_PM_GO_LINKD 0x0020 /* Go Link Disconnect */ - -#define E1000_MPHY_DIS_ACCESS 0x80000000 /* disable_access bit */ -#define E1000_MPHY_ENA_ACCESS 0x40000000 /* enable_access bit */ -#define E1000_MPHY_BUSY 0x00010000 /* busy bit */ -#define E1000_MPHY_ADDRESS_FNC_OVERRIDE 0x20000000 /* fnc_override bit */ -#define E1000_MPHY_ADDRESS_MASK 0x0000FFFF /* address mask */ - -#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4 -#define IGP01E1000_PHY_POLARITY_MASK 0x0078 - -#define IGP01E1000_PSCR_AUTO_MDIX 0x1000 -#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */ - -#define IGP01E1000_PSCFR_SMART_SPEED 0x0080 - -#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */ -#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */ -#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */ - -#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000 - -#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002 -#define IGP01E1000_PSSR_MDIX 0x0800 -#define IGP01E1000_PSSR_SPEED_MASK 0xC000 -#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000 - -#define IGP02E1000_PHY_CHANNEL_NUM 4 -#define IGP02E1000_PHY_AGC_A 0x11B1 -#define IGP02E1000_PHY_AGC_B 0x12B1 -#define IGP02E1000_PHY_AGC_C 0x14B1 -#define IGP02E1000_PHY_AGC_D 0x18B1 - -#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Course=15:13, Fine=12:9 */ -#define IGP02E1000_AGC_LENGTH_MASK 0x7F -#define IGP02E1000_AGC_RANGE 15 - -#define E1000_CABLE_LENGTH_UNDEFINED 0xFF - -#define E1000_KMRNCTRLSTA_OFFSET 0x001F0000 -#define E1000_KMRNCTRLSTA_OFFSET_SHIFT 16 -#define E1000_KMRNCTRLSTA_REN 0x00200000 -#define E1000_KMRNCTRLSTA_DIAG_OFFSET 0x3 /* Kumeran Diagnostic */ -#define E1000_KMRNCTRLSTA_TIMEOUTS 0x4 /* Kumeran Timeouts */ -#define E1000_KMRNCTRLSTA_INBAND_PARAM 0x9 /* Kumeran InBand Parameters */ -#define E1000_KMRNCTRLSTA_IBIST_DISABLE 0x0200 /* Kumeran IBIST Disable */ -#define E1000_KMRNCTRLSTA_DIAG_NELPBK 0x1000 /* Nearend Loopback mode */ - -#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 -#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY Special Ctrl */ -#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY Special and LED Ctrl */ -#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control */ - -/* IFE PHY Extended Status Control */ -#define IFE_PESC_POLARITY_REVERSED 0x0100 - -/* IFE PHY Special Control */ -#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 -#define IFE_PSC_FORCE_POLARITY 0x0020 - -/* IFE PHY Special Control and LED Control */ -#define IFE_PSCL_PROBE_MODE 0x0020 -#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */ -#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */ - -/* IFE PHY MDIX Control */ -#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */ -#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDI-X, 0=force MDI */ -#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable auto, 0=disable */ - -/* SFP modules ID memory locations */ -#define E1000_SFF_IDENTIFIER_OFFSET 0x00 -#define E1000_SFF_IDENTIFIER_SFF 0x02 -#define E1000_SFF_IDENTIFIER_SFP 0x03 - -#define E1000_SFF_ETH_FLAGS_OFFSET 0x06 -/* Flags for SFP modules compatible with ETH up to 1Gb */ -struct sfp_e1000_flags { - u8 e1000_base_sx:1; - u8 e1000_base_lx:1; - u8 e1000_base_cx:1; - u8 e1000_base_t:1; - u8 e100_base_lx:1; - u8 e100_base_fx:1; - u8 e10_base_bx10:1; - u8 e10_base_px:1; -}; - -/* Vendor OUIs: format of OUI is 0x[byte0][byte1][byte2][00] */ -#define E1000_SFF_VENDOR_OUI_TYCO 0x00407600 -#define E1000_SFF_VENDOR_OUI_FTL 0x00906500 -#define E1000_SFF_VENDOR_OUI_AVAGO 0x00176A00 -#define E1000_SFF_VENDOR_OUI_INTEL 0x001B2100 - -#endif |