docs: cleanup typos on readthrough

Type: style

Change-Id: I3b15035ea6c13cd1ca3cdc9dfa9b10a6e1be9880
Signed-off-by: Paul Vinciguerra <pvinci@vinciconsulting.com>

3 files changed, 10 insertions, 10 deletions

diff --git a/docs/gettingstarted/users/configuring/hugepages.rst b/docs/gettingstarted/users/configuring/hugepages.rst
index 3019a203c79..7a1e0bd8057 100644
--- a/docs/gettingstarted/users/configuring/hugepages.rst
+++ b/docs/gettingstarted/users/configuring/hugepages.rst
@@ -24,7 +24,7 @@ the hugepage settings, perform the following commands:
     # All groups allowed to access hugepages
     vm.hugetlb_shm_group=0
     
-    # Shared Memory Max must be greator or equal to the total size of hugepages.
+    # Shared Memory Max must be greater or equal to the total size of hugepages.
     # For 2MB pages, TotalHugepageSize = vm.nr_hugepages * 2 * 1024 * 1024
     # If the existing kernel.shmmax setting  (cat /sys/proc/kernel/shmmax)
     # is greater than the calculated TotalHugepageSize then set this parameter
diff --git a/docs/gettingstarted/users/configuring/startup.rst b/docs/gettingstarted/users/configuring/startup.rst
index df96ff7ae2e..7a663944261 100644
--- a/docs/gettingstarted/users/configuring/startup.rst
+++ b/docs/gettingstarted/users/configuring/startup.rst
@@ -244,7 +244,7 @@ attributes.
      **Example:** cli-prompt vpp-2
      
  * **cli-history-limit <n>**
-     Limit commmand history to <n> lines. A value of 0 disables command history.
+     Limit command history to <n> lines. A value of 0 disables command history.
      Default value: 50
      
      **Example:** cli-history-limit 100
@@ -336,7 +336,7 @@ Popular options include:
           for all NICs except VICs, using ENIC driver, which has VLAN stripping on
           by default.
       * **hqos**
-          Enable the Hierarchical Quaity-of-Service (HQoS) scheduler, default is
+          Enable the Hierarchical Quality-of-Service (HQoS) scheduler, default is
           disabled. This enables HQoS on specific output interface.
       * **hqos { .. }**
           HQoS can also have its own set of custom parameters. Setting a custom
@@ -413,7 +413,7 @@ Popular options include:
      **Example:** enable-tcp-udp-checksum
 
  * **no-multi-seg**
-     Disable mutli-segment buffers, improves performance but disables Jumbo MTU
+     Disable multi-segment buffers, improves performance but disables Jumbo MTU
      support.
      
      **Example:** no-multi-seg
@@ -435,7 +435,7 @@ Popular options include:
      **Example:** log-level error
 
  * **dev default { .. }**
-     Change default settings for all intefaces. This sections supports the
+     Change default settings for all interfaces. This sections supports the
      same set of custom parameters described in *'dev <pci-dev> { .. }*'.
      
      **Example:**
@@ -1216,8 +1216,8 @@ ____________________
 
 A plugin can be disabled by default. It may still be in an experimental phase
 or only be needed in special circumstances. If this is the case, the plugin can
-be explicitely enabled in *'startup.conf'*. Also, a plugin that is enabled by
-default can be explicitely disabled in *'startup.conf'*.
+be explicitly enabled in *'startup.conf'*. Also, a plugin that is enabled by
+default can be explicitly disabled in *'startup.conf'*.
 
 Another useful use of this section is to disable all the plugins, then enable
 only the plugins that are desired.
diff --git a/docs/gettingstarted/users/configutil/sysinfo.rst b/docs/gettingstarted/users/configutil/sysinfo.rst
index 893f94999ce..77dd1c778c2 100644
--- a/docs/gettingstarted/users/configutil/sysinfo.rst
+++ b/docs/gettingstarted/users/configutil/sysinfo.rst
@@ -11,15 +11,15 @@ Threads
 -------
 
 It usually is not needed, but VPP can be configured to run on isolated CPUs. In the example shown
-VPP is configured with 2 workers. The main thread is also configured to run on a seperate CPU. The
-stats thread will always run on CPU 0. This utilty will put the worker threads on CPUs that are
+VPP is configured with 2 workers. The main thread is also configured to run on a separate CPU. The
+stats thread will always run on CPU 0. This utility will put the worker threads on CPUs that are
 associated with the ports that are configured.
 
 Grub Command Line
 -----------------
 
 In general the Grub command line does not need to be changed. If the system is running many processes
-it may be neccessary to isolate CPUs for VPP or other processes.
+it may be necessary to isolate CPUs for VPP or other processes.
 
 Huge Pages
 ----------