aboutsummaryrefslogtreecommitdiffstats
path: root/docs/usecases
diff options
context:
space:
mode:
authorJohn DeNisco <jdenisco@cisco.com>2018-08-01 10:38:23 -0400
committerDamjan Marion <dmarion@me.com>2018-08-01 20:21:23 +0000
commita14c16674023bd6672ca49e3551c707702711050 (patch)
tree8f6fcd2a22356a0d16dce12f3b2bbdefbb37d7e7 /docs/usecases
parente126cc53317fcc38970d244bea2ddaf11e47702f (diff)
docs: change code blocks from "shell" to "console"
Change-Id: I136fccfc06e07fb68d11df686c59687362fb8827 Signed-off-by: John DeNisco <jdenisco@cisco.com>
Diffstat (limited to 'docs/usecases')
-rw-r--r--docs/usecases/Routing.rst30
-rw-r--r--docs/usecases/containerCreation.rst28
-rw-r--r--docs/usecases/containerSetup.rst8
3 files changed, 33 insertions, 33 deletions
diff --git a/docs/usecases/Routing.rst b/docs/usecases/Routing.rst
index 0c5908fd57e..cecc2637108 100644
--- a/docs/usecases/Routing.rst
+++ b/docs/usecases/Routing.rst
@@ -9,7 +9,7 @@ Now for connecting these two linux containers to VPP and pinging between them.
Enter container *cone*, and check the current network configuration:
-.. code-block:: console
+.. code-block:: shell
root@cone:/# ip -o a
1: lo inet 127.0.0.1/8 scope host lo\ valid_lft forever preferred_lft forever
@@ -24,7 +24,7 @@ Notice that *veth_link1* has no assigned IP.
Check if the interfaces are down or up:
-.. code-block:: console
+.. code-block:: shell
root@cone:/# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1
@@ -42,7 +42,7 @@ Check if the interfaces are down or up:
Make sure your loopback interface is up, and assign an IP and gateway to veth_link1.
-.. code-block:: console
+.. code-block:: shell
root@cone:/# ip link set dev lo up
root@cone:/# ip addr add 172.16.1.2/24 dev veth_link1
@@ -54,7 +54,7 @@ Here, the IP is 172.16.1.2/24 and the gateway is 172.16.1.1.
Run some commands to verify the changes:
-.. code-block:: console
+.. code-block:: shell
root@cone:/# ip -o a
1: lo inet 127.0.0.1/8 scope host lo\ valid_lft forever preferred_lft forever
@@ -77,7 +77,7 @@ Now exit this container and repeat this process with container *ctwo*, except wi
After thats done for *both* containers, exit from the container if you're in one:
-.. code-block:: console
+.. code-block:: shell
root@ctwo:/# exit
exit
@@ -85,7 +85,7 @@ After thats done for *both* containers, exit from the container if you're in one
In the machine running the containers, run **ip link** to see the host *veth* network interfaces, and their link with their respective *container veth's*.
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# ip link
1: lo: <LOOPBACK> mtu 65536 qdisc noqueue state DOWN mode DEFAULT group default qlen 1
@@ -112,7 +112,7 @@ Remember our network interface index 32 in *cone* from this :ref:`note <networkN
With VPP in the host machine, show current VPP interfaces:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# vppctl show inter
Name Idx State MTU (L3/IP4/IP6/MPLS) Counter Count
@@ -122,14 +122,14 @@ Which should only output local0.
Based on the names of the network interfaces discussed previously, which are specific to my systems, we can create VPP host-interfaces:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# vppctl create host-interface name vethQL7K0C
root@localhost:~# vppctl create host-interface name veth8NA72P
Verify they have been set up properly:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# vppctl show inter
Name Idx State MTU (L3/IP4/IP6/MPLS) Counter Count
@@ -142,14 +142,14 @@ Which should output *three network interfaces*, local0, and the other two host n
Set their state to up:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# vppctl set interface state host-vethQL7K0C up
root@localhost:~# vppctl set interface state host-veth8NA72P up
Verify they are now up:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# vppctl show inter
Name Idx State MTU (L3/IP4/IP6/MPLS) Counter Count
@@ -160,7 +160,7 @@ Verify they are now up:
Add IP addresses for the other end of each veth link:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# vppctl set interface ip address host-vethQL7K0C 172.16.1.1/24
root@localhost:~# vppctl set interface ip address host-veth8NA72P 172.16.2.1/24
@@ -168,7 +168,7 @@ Add IP addresses for the other end of each veth link:
Verify the addresses are set properly by looking at the L3 table:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# vppctl show inter addr
host-vethQL7K0C (up):
@@ -179,7 +179,7 @@ Verify the addresses are set properly by looking at the L3 table:
Or looking at the FIB by doing:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# vppctl show ip fib
ipv4-VRF:0, fib_index:0, flow hash:[src dst sport dport proto ] locks:[src:plugin-hi:2, src:default-route:1, ]
@@ -238,7 +238,7 @@ Or looking at the FIB by doing:
At long last you probably want to see some pings:
-.. code-block:: console
+.. code-block:: shell
root@localhost:~# lxc-attach -n cone -- ping -c3 172.16.2.2
PING 172.16.2.2 (172.16.2.2) 56(84) bytes of data.
diff --git a/docs/usecases/containerCreation.rst b/docs/usecases/containerCreation.rst
index b9344f35ce5..fb38b3ed135 100644
--- a/docs/usecases/containerCreation.rst
+++ b/docs/usecases/containerCreation.rst
@@ -7,13 +7,13 @@ ___________________
First you should have root privileges:
-.. code-block:: console
+.. code-block:: shell
- $ sudo bash
+ ~$ sudo bash
Then install packages for containers such as lxc:
-.. code-block:: console
+.. code-block:: shell
# apt-get install bridge-utils lxc
@@ -26,9 +26,9 @@ Since we want to ping between two containers, we'll need to **add to this file**
Look at the contents of *default.conf*, which should initially look like this:
-.. code-block:: console
+.. code-block:: shell
- # cat /etc/lxc/default.conf
+ # cat /etc/lxc/default.conf
lxc.network.type = veth
lxc.network.link = lxcbr0
lxc.network.flags = up
@@ -40,15 +40,15 @@ Now you will *append to this file* so that each container you create will have a
You can do this by piping *echo* output into *tee*, where each line is separated with a newline character *\\n* as shown below. Alternatively, you can manually add to this file with a text editor such as **vi**, but make sure you have root privileges.
-.. code-block:: console
+.. code-block:: shell
# echo -e "lxc.network.name = veth0\nlxc.network.type = veth\nlxc.network.name = veth_link1" | sudo tee -a /etc/lxc/default.conf
Inspect the contents again to verify the file was indeed modified:
-.. code-block:: console
+.. code-block:: shell
- # cat /etc/lxc/default.conf
+ # cat /etc/lxc/default.conf
lxc.network.type = veth
lxc.network.link = lxcbr0
lxc.network.flags = up
@@ -62,7 +62,7 @@ After this, we're ready to create the containers.
Creates an Ubuntu Xenial container named "cone".
-.. code-block:: console
+.. code-block:: shell
# lxc-create -t download -n cone -- --dist ubuntu --release xenial --arch amd64 --keyserver hkp://p80.pool.sks-keyservers.net:80
@@ -79,7 +79,7 @@ If successful, you'll get an output similar to this:
Make another container "ctwo".
-.. code-block:: console
+.. code-block:: shell
# lxc-create -t download -n ctwo -- --dist ubuntu --release xenial --arch amd64 --keyserver hkp://p80.pool.sks-keyservers.net:80
@@ -87,7 +87,7 @@ Make another container "ctwo".
List your containers to verify they exist:
-.. code-block:: console
+.. code-block:: shell
# lxc-ls
cone ctwo
@@ -95,13 +95,13 @@ List your containers to verify they exist:
Start the first container:
-.. code-block:: console
+.. code-block:: shell
# lxc-start --name cone
And verify its running:
-.. code-block:: console
+.. code-block:: shell
# lxc-ls --fancy
NAME STATE AUTOSTART GROUPS IPV4 IPV6
@@ -114,7 +114,7 @@ And verify its running:
Here are some `lxc container commands <https://help.ubuntu.com/lts/serverguide/lxc.html.en-GB#lxc-basic-usage>`_ you may find useful:
- .. code-block:: console
+ .. code-block:: shell
sudo lxc-ls --fancy
sudo lxc-start --name u1 --daemon
diff --git a/docs/usecases/containerSetup.rst b/docs/usecases/containerSetup.rst
index e0fd81eebc3..d1c230daf24 100644
--- a/docs/usecases/containerSetup.rst
+++ b/docs/usecases/containerSetup.rst
@@ -9,14 +9,14 @@ Now we can go into container *cone* and install prerequisites such as VPP, and p
To enter our container via the shell, type:
-.. code-block:: console
+.. code-block:: shell
# lxc-attach -n cone
root@cone:/#
Run the linux DHCP setup and install VPP:
-.. code-block:: console
+.. code-block:: shell
root@cone:/# resolvconf -d eth0
root@cone:/# dhclient
@@ -28,13 +28,13 @@ Run the linux DHCP setup and install VPP:
After this is done, start VPP in this container:
-.. code-block:: console
+.. code-block:: shell
root@cone:/# service vpp start
Exit this container with the **exit** command (you *may* need to run **exit** twice):
-.. code-block:: console
+.. code-block:: shell
root@cone:/# exit
exit