diff options
Diffstat (limited to 'docs/gettingstarted/users')
| -rw-r--r-- | docs/gettingstarted/users/configuring/hugepages.rst | 2 | ||||
| -rw-r--r-- | docs/gettingstarted/users/configuring/startup.rst | 12 | ||||
| -rw-r--r-- | docs/gettingstarted/users/configutil/sysinfo.rst | 6 |
3 files changed, 10 insertions, 10 deletions
diff --git a/docs/gettingstarted/users/configuring/hugepages.rst b/docs/gettingstarted/users/configuring/hugepages.rst index 3019a203c79..7a1e0bd8057 100644 --- a/docs/gettingstarted/users/configuring/hugepages.rst +++ b/docs/gettingstarted/users/configuring/hugepages.rst @@ -24,7 +24,7 @@ the hugepage settings, perform the following commands: # All groups allowed to access hugepages vm.hugetlb_shm_group=0 - # Shared Memory Max must be greator or equal to the total size of hugepages. + # Shared Memory Max must be greater or equal to the total size of hugepages. # For 2MB pages, TotalHugepageSize = vm.nr_hugepages * 2 * 1024 * 1024 # If the existing kernel.shmmax setting (cat /sys/proc/kernel/shmmax) # is greater than the calculated TotalHugepageSize then set this parameter diff --git a/docs/gettingstarted/users/configuring/startup.rst b/docs/gettingstarted/users/configuring/startup.rst index df96ff7ae2e..7a663944261 100644 --- a/docs/gettingstarted/users/configuring/startup.rst +++ b/docs/gettingstarted/users/configuring/startup.rst @@ -244,7 +244,7 @@ attributes. **Example:** cli-prompt vpp-2 * **cli-history-limit <n>** - Limit commmand history to <n> lines. A value of 0 disables command history. + Limit command history to <n> lines. A value of 0 disables command history. Default value: 50 **Example:** cli-history-limit 100 @@ -336,7 +336,7 @@ Popular options include: for all NICs except VICs, using ENIC driver, which has VLAN stripping on by default. * **hqos** - Enable the Hierarchical Quaity-of-Service (HQoS) scheduler, default is + Enable the Hierarchical Quality-of-Service (HQoS) scheduler, default is disabled. This enables HQoS on specific output interface. * **hqos { .. }** HQoS can also have its own set of custom parameters. Setting a custom @@ -413,7 +413,7 @@ Popular options include: **Example:** enable-tcp-udp-checksum * **no-multi-seg** - Disable mutli-segment buffers, improves performance but disables Jumbo MTU + Disable multi-segment buffers, improves performance but disables Jumbo MTU support. **Example:** no-multi-seg @@ -435,7 +435,7 @@ Popular options include: **Example:** log-level error * **dev default { .. }** - Change default settings for all intefaces. This sections supports the + Change default settings for all interfaces. This sections supports the same set of custom parameters described in *'dev <pci-dev> { .. }*'. **Example:** @@ -1216,8 +1216,8 @@ ____________________ A plugin can be disabled by default. It may still be in an experimental phase or only be needed in special circumstances. If this is the case, the plugin can -be explicitely enabled in *'startup.conf'*. Also, a plugin that is enabled by -default can be explicitely disabled in *'startup.conf'*. +be explicitly enabled in *'startup.conf'*. Also, a plugin that is enabled by +default can be explicitly disabled in *'startup.conf'*. Another useful use of this section is to disable all the plugins, then enable only the plugins that are desired. diff --git a/docs/gettingstarted/users/configutil/sysinfo.rst b/docs/gettingstarted/users/configutil/sysinfo.rst index 893f94999ce..77dd1c778c2 100644 --- a/docs/gettingstarted/users/configutil/sysinfo.rst +++ b/docs/gettingstarted/users/configutil/sysinfo.rst @@ -11,15 +11,15 @@ Threads ------- It usually is not needed, but VPP can be configured to run on isolated CPUs. In the example shown -VPP is configured with 2 workers. The main thread is also configured to run on a seperate CPU. The -stats thread will always run on CPU 0. This utilty will put the worker threads on CPUs that are +VPP is configured with 2 workers. The main thread is also configured to run on a separate CPU. The +stats thread will always run on CPU 0. This utility will put the worker threads on CPUs that are associated with the ports that are configured. Grub Command Line ----------------- In general the Grub command line does not need to be changed. If the system is running many processes -it may be neccessary to isolate CPUs for VPP or other processes. +it may be necessary to isolate CPUs for VPP or other processes. Huge Pages ---------- |