diff options
Diffstat (limited to 'src/plugins/ioam/ioam_ipv6_doc.md')
| -rw-r--r-- | src/plugins/ioam/ioam_ipv6_doc.md | 530 |
1 files changed, 530 insertions, 0 deletions
diff --git a/src/plugins/ioam/ioam_ipv6_doc.md b/src/plugins/ioam/ioam_ipv6_doc.md new file mode 100644 index 00000000000..305375fa239 --- /dev/null +++ b/src/plugins/ioam/ioam_ipv6_doc.md @@ -0,0 +1,530 @@ +## IOAM for IPv6 {#ioam_ipv6_doc} +IOAM data is transported as options in an IPv6 hop-by-hop extension header. + +### Export of IOAM data +IPv6 IOAM hop-by-hop data collected is exported as IPfix records. +#### Export data format and flow +- Capturing sections of selected packets: First few cachelines of packet starting at IP6 header is copied and appended into a MTU sized buffer. +- Encoding of the data captured: IPFIX is used with new template ID to indicate raw binary data export that is first 192 octets starting at IPv6 header, padded if the total length of packet is less than 192 octets. So no formatting of the data is required – we could call it “bulk transport of telemetry data over IPFIX”. +- Sections of captured packets are appended to the buffer – This buffer contains an homogenous ipfix data set so no additional formatting is needed. It is then up to the IPFIX collector to parse, filter, and transform the data into the desired format for a particular deployment or use-case +- Preparing the data for export: slapping the IP, UDP and IPfix header onto the captured set of buffer. +- Sending the data : When the buffers are full they are flushed out and replaced. When the packet rate is low then periodically ipfix packets are flushed from per thread buffers. +[https://gerrit.fd.io/r/#/c/2267] brings in this support. + +Performance on a node where iOAM data is exported and removed: + + Name State Calls Vectors Suspends Clocks Vectors/Call + ip6-export active 1145933 272387308 0 1.12e2 237.69 + ip6-hop-by-hop active 1145933 272387308 0 4.25e1 237.69 + ip6-pop-hop-by-hop active 1145933 272387308 0 4.41e1 237.69 + +## Configuration +Configuring IOAM involves: +- Selecting the packets for which IOAM data must be inserted, updated or removed + - Selection of packets for IOAM data insertion on IOAM encapsulating node. + Selection of packets is done by 5-tuple based classification + - Selection of packets for updating IOAM data is implicitly done on the + presence of IOAM options in the packet + - Selection of packets for removing the IOAM data is done on 5-tuple + based classification +- The kind of data to be collected + - Tracing data + - Proof of transit + - Edge-to-Edge sequence numbers +- Additional details for processing IOAM data to be collected + - For trace data - trace type, number of nodes to be recorded in the trace, + time stamp precision, etc. + - For POT data - configuration of POT profile required to process the POT data + - Enabling sequence numbers per classified flows + +The CLI for configuring IOAM is explained here followed by detailed steps +and examples to deploy IOAM on VPP as an encapsulating, transit or +decapsulating IOAM node in the subsequent sub-sections. + +VPP IOAM configuration for creating trace profile and enabling trace: + + # set ioam-trace profile trace-type <0x1f|0x7|0x9|0x11|0x19> + trace-elts <number of trace elements> trace-tsp <0|1|2|3> + node-id <node ID in hex> app-data <application data in hex> + + +A description of each of the options of the CLI follows: +- trace-type : An entry in the "Node data List" array of the trace option +can have different formats, following the needs of the a deployment. +For example: Some deployments might only be interested +in recording the node identifiers, whereas others might be interested +in recording node identifier and timestamp. +The following types are currently supported: + - 0x1f : Node data to include hop limit (8 bits), node ID (24 bits), + ingress and egress interface IDs (16 bits each), timestamp (32 bits), + application data (32 bits) + - 0x7 : Node data to include hop limit (8 bits), node ID (24 bits), + ingress and egress interface IDs (16 bits each) + - 0x9 : Node data to include hop limit (8 bits), node ID (24 bits), + timestamp (32 bits) + - 0x11: Node data to include hop limit (8 bits), node ID (24 bits), + application data (32 bits) + - 0x19: Node data to include hop limit (8 bits), node ID (24 bits), + timestamp (32 bits), application data (32 bits) +- trace-elts : Defines the length of the node data array in the trace option. +- trace-tsp : Defines the timestamp precision to use with the enumerated value + for precision as follows: + - 0 : 32bits timestamp in seconds + - 1 : 32bits timestamp in milliseconds + - 2 : 32bits timestamp in microseconds + - 3 : 32bits timestamp in nanoseconds +- node-id : Unique identifier for the node, included in the node ID + field of the node data in trace option. +- app-data : The value configured here is included as is in +application data field of node data in trace option. + +Enabling trace is done by setting "trace" in the following command: + + + # set ioam [trace] [pot] [seqno] [analyse] + +### Trace configuration + +#### On IOAM encapsulating node + - **Configure classifier and apply ACL** to select packets for + IOAM data insertion + - Example to enable IOAM data insertion for all the packets + towards IPv6 address db06::06: + + vpp# classify table acl-miss-next ip6-node ip6-lookup mask l3 ip6 dst + + vpp# classify session acl-hit-next ip6-node ip6-add-syn-hop-by-hop + table-index 0 match l3 ip6 dst db06::06 ioam-encap test-encap + + vpp# set int input acl intfc GigabitEthernet0/0/0 ip6-table 0 + + - **Enable tracing** : Specify node ID, maximum number of nodes for which + trace data should be recorded, type of data to be included for recording, + optionally application data to be included + - Example to enable tracing with a maximum of 4 nodes recorded + and the data to be recorded to include - hop limit, node id, + ingress and egress interface IDs, timestamp (millisecond precision), + application data (0x1234): + + + vpp# set ioam-trace profile trace-type 0x1f trace-elts 4 trace-tsp 1 + node-id 0x1 app-data 0x1234 + vpp# set ioam rewrite trace + + +#### On IOAM transit node +- The transit node requires trace type, timestamp precision, node ID and +optionally application data to be configured, +to update its node data in the trace option. + +Example: + + vpp# set ioam-trace profile trace-type 0x1f trace-elts 4 trace-tsp 1 + node-id 0x2 app-data 0x1234 + +#### On the IOAM decapsulating node +- The decapsulating node similar to encapsulating node requires +**classification** of the packets to remove IOAM data from. + - Example to decapsulate IOAM data for packets towards + db06::06, configure classifier and enable it as an ACL as follows: + + + vpp# classify table acl-miss-next ip6-node ip6-lookup mask l3 ip6 dst + + vpp# classify session acl-hit-next ip6-node ip6-lookup table-index 0 + match l3 ip6 dst db06::06 ioam-decap test-decap + + vpp# set int input acl intfc GigabitEthernet0/0/0 ip6-table 0 + + +- Decapsulating node requires trace type, timestamp precision, +node ID and optionally application data to be configured, +to update its node data in the trace option before it is decapsulated. + +Example: + + vpp# set ioam-trace profile trace-type 0x1f trace-elts 4 + trace-tsp 1 node-id 0x3 app-data 0x1234 + + +### Proof of Transit configuration + +For details on proof-of-transit, +see the IETF draft [IOAM-ietf-proof-of-transit]. +To enable Proof of Transit all the nodes that participate +and hence are verified for transit need a proof of transit profile. +A script to generate a proof of transit profile as per the mechanism +described in [IOAM-ietf-proof-of-transit] will be available at [IOAM-Devnet]. + +The Proof of transit mechanism implemented here is based on +Shamir's Secret Sharing algorithm. +The overall algorithm uses two polynomials +POLY-1 and POLY-2. The degree of polynomials depends on number of nodes +to be verified for transit. +POLY-1 is secret and constant. Each node gets a point on POLY-1 +at setup-time and keeps it secret. +POLY-2 is public, random and per packet. +Each node is assigned a point on POLY-1 and POLY-2 with the same x index. +Each node derives its point on POLY-2 each time a packet arrives at it. +A node then contributes its points on POLY-1 and POLY-2 to construct +POLY-3 (POLY-3 = POLY-1 + POLY-2) using lagrange extrapolation and +forwards it towards the verifier by updating POT data in the packet. +The verifier constructs POLY-3 from the accumulated value from all the nodes +and its own points on POLY-1 and POLY-2 and verifies whether +POLY-3 = POLY-1 + POLY-2. Only the verifier knows POLY-1. +The solution leverages finite field arithmetic in a field of size "prime number" +for reasons explained in description of Shamir's secret sharing algorithm. + +Here is an explanation of POT profile list and profile configuration CLI to +realize the above mechanism. +It is best to use the script provided at [IOAM-Devnet] to generate +this configuration. +- **Create POT profile** : set pot profile name <string> id [0-1] +[validator-key 0xu64] prime-number 0xu64 secret_share 0xu64 +lpc 0xu64 polynomial2 0xu64 bits-in-random [0-64] + - name : Profile list name. + - id : Profile id, it can be 0 or 1. + A maximum of two profiles can be configured per profile list. + - validator-key : Secret key configured only on the + verifier/decapsulating node used to compare and verify proof of transit. + - prime-number : Prime number for finite field arithmetic as required by the + proof of transit mechanism. + - secret_share : Unique point for each node on the secret polynomial POLY-1. + - lpc : Lagrange Polynomial Constant(LPC) calculated per node based on + its point (x value used for evaluating the points on the polynomial) + on the polynomial used in lagrange extrapolation + for reconstructing polynomial (POLY-3). + - polynomial2 : Is the pre-evaluated value of the point on + 2nd polynomial(POLY-2). This is unique for each node. + It is pre-evaluated for all the coefficients of POLY-2 except + for the constant part of the polynomial that changes per packet + and is received as part of the POT data in the packet. + - bits-in-random : To control the size of the random number to be + generated. This number has to match the other numbers generated and used + in the profile as per the algorithm. + +- **Set a configured profile as active/in-use** : +set pot profile-active name <string> ID [0-1] + - name : Name of the profile list to be used for computing + POT data per packet. + - ID : Identifier of the profile within the list to be used. + +- **Enable POT**: +set ioam rewrite pot + +#### On IOAM encapsulating node + - Configure the classifier and apply ACL to select packets for IOAM data insertion. + - Example to enable IOAM data insertion for all the packet towards + IPv6 address db06::06 - + + vpp# classify table miss-next ip6-node ip6-lookup mask l3 ip6 dst + + vpp# classify session acl-hit-next ip6-node + ip6-add-hop-by-hop table-index 0 match l3 ip6 dst db06::06 ioam-encap test-encap + + vpp# set int input acl intfc GigabitEthernet0/0/0 ip6-table 0 + + + - Configure the proof of transit profile list with profiles. +Each profile list referred to by a name can contain 2 profiles, +only one is in use for updating proof of transit data at any time. + - Example profile list example with a profile generated from the + script to verify transit through 3 nodes is: + + + vpp# set pot profile name example id 0 prime-number 0x7fff0000fa884685 + secret_share 0x6c22eff0f45ec56d lpc 0x7fff0000fa884682 + polynomial2 0xffb543d4a9c bits-in-random 63 + + - Enable one of the profiles from the configured profile list as active + so that is will be used for calculating proof of transit + +Example enable profile ID 0 from profile list example configured above: + + + vpp# set pot profile-active name example ID 0 + + + - Enable POT option to be inserted + + + vpp# set ioam rewrite pot + + +#### On IOAM transit node + - Configure the proof of transit profile list with profiles for transit node. +Example: + + + vpp# set pot profile name example id 0 prime-number 0x7fff0000fa884685 + secret_share 0x564cdbdec4eb625d lpc 0x1 + polynomial2 0x23f3a227186a bits-in-random 63 + +#### On IOAM decapsulating node / verifier +- The decapsulating node, similar to the encapsulating node requires +classification of the packets to remove IOAM data from. + - Example to decapsulate IOAM data for packets towards db06::06 + configure classifier and enable it as an ACL as follows: + + + vpp# classify table miss-next ip6-node ip6-lookup mask l3 ip6 dst + + vpp# classify session acl-hit-next ip6-node ip6-lookup table-index 0 + match l3 ip6 dst db06::06 ioam-decap test-decap + + vpp# set int input acl intfc GigabitEthernet0/0/0 ip6-table 0 ioam-decap test-decap + +- To update and verify the proof of transit, POT profile list should be configured. + - Example POT profile list configured as follows: + + vpp# set pot profile name example id 0 validate-key 0x7fff0000fa88465d + prime-number 0x7fff0000fa884685 secret_share 0x7a08fbfc5b93116d lpc 0x3 + polynomial2 0x3ff738597ce bits-in-random 63 + +### Configuration to enable sequence numbers +#### On IOAM encapsulating node + - Configure the classifier and apply ACL to select packets for IOAM data insertion. + - Example to enable IOAM data insertion for all the packet towards + IPv6 address db06::06 - + + vpp# classify table miss-next ip6-node ip6-lookup mask l3 ip6 dst + + vpp# classify session acl-hit-next ip6-node + ip6-add-hop-by-hop table-index 0 match l3 ip6 dst db06::06 ioam-encap test-encap + + vpp# set int input acl intfc GigabitEthernet0/0/0 ip6-table 0 + +To enable insertion of sequence numbers on the IOAM encapsulation node do the following: + + set ioam rewrite seqno + +This will create and insert a unique sequence numbers for every flow matching a classify session. + +On IOAM decapsulating node to analyze the sequence numbers do the following: + +- Configure the classifier and apply ACL to select packets for IOAM data removal. + - Example to enable IOAM data insertion for all the packet towards + IPv6 address db06::06 - + + vpp# classify table miss-next ip6-node ip6-lookup mask l3 ip6 dst + + vpp# classify session acl-hit-next ip6-node + ip6-add-hop-by-hop table-index 0 match l3 ip6 dst db06::06 ioam-decap test-decap + + vpp# set int input acl intfc GigabitEthernet0/0/0 ip6-table 0 + +Following command will analyze the sequence numbers received: + + set ioam rewrite analyse + +### Export configuration +On IOAM decapsulating node where trace is decap is configured add the following: + + set ioam export ipfix collector <ip4-address> src <ip4-address> + +## Operational data + +Following CLIs are available to check IOAM operation: +- To check IOAM configuration that are effective use "show IOAM summary" + +Example: + + vpp# show ioam summary + REWRITE FLOW CONFIGS - Not configured + HOP BY HOP OPTIONS - TRACE CONFIG - + Trace Type : 0x1f (31) + Trace timestamp precision : 1 (Milliseconds) + Num of trace nodes : 4 + Node-id : 0x2 (2) + App Data : 0x1234 (4660) + POT OPTION - 1 (Enabled) + Try 'show IOAM pot and show pot profile' for more information + +- To find statistics about packets for which IOAM options were +added (encapsulating node) and removed (decapsulating node) execute +**show errors** + +Example on encapsulating node: + + + vpp# show error + Count Node Reason + 1208804706 ip6-inacl input ACL hits + 1208804706 ip6-add-hop-by-hop Pkts w/ added ip6 hop-by-hop options + +Example on decapsulating node: + + vpp# show error + Count Node Reason + 69508569 ip6-inacl input ACL hits + 69508569 ip6-pop-hop-by-hop Pkts w/ removed ip6 hop-by-hop options + +- To check the POT profiles use "show pot profile" + +Example: + + vpp# show pot profile + Profile list in use : example + POT Profile at index: 0 + ID : 0 + Validator : False (0) + Secret share : 0x564cdbdec4eb625d (6218586935324795485) + Prime number : 0x7fff0000fa884685 (9223090566081300101) + 2nd polynomial(eval) : 0x23f3a227186a (39529304496234) + LPC : 0x1 (1) + Bit mask : 0x7fffffffffffffff (9223372036854775807) + Profile index in use: 0 + Pkts passed : 0x36 (54) + +- To get statistics of POT for packets use "show IOAM pot" + +Example at encapsulating or transit node: + + vpp# show ioam pot + Pkts with ip6 hop-by-hop POT options - 54 + Pkts with ip6 hop-by-hop POT options but no profile set - 0 + Pkts with POT in Policy - 0 + Pkts with POT out of Policy - 0 + + +Example at decapsulating/verification node: + + + vpp# show ioam pot + Pkts with ip6 hop-by-hop POT options - 54 + Pkts with ip6 hop-by-hop POT options but no profile set - 0 + Pkts with POT in Policy - 54 + Pkts with POT out of Policy - 0 + + +- For statistics on number of packets processed for trace execute **show ioam trace** + + + vpp# show ioam trace + Pkts with ip6 hop-by-hop trace options - 0 + Pkts with ip6 hop-by-hop trace options but no profile set - 0 + Pkts with trace updated - 0 + Pkts with trace options but no space - 0 + +- For statistics and information on sequence number processing execute **show ioam e2e** +On IOAM encapsulating node: + + + vpp# show ioam e2e + IOAM E2E information: + Flow name: test-encap + SeqNo Data: + Current Seq. Number : 156790 + +On IOAM decapsulating node: + + + vpp# show ioam e2e + IOAM E2E information: + Flow name: test-decap + SeqNo Data: + Current Seq. Number : 156789 + Highest Seq. Number : 156789 + Packets received : 156789 + Lost packets : 0 + Reordered packets : 0 + Duplicate packets : 0 + + Flow name: test-decap2 + SeqNo Data: + Current Seq. Number : 0 + Highest Seq. Number : 0 + Packets received : 0 + Lost packets : 0 + Reordered packets : 0 + Duplicate packets : 0 + +- Tracing - enable trace of IPv6 packets to view the data inserted and +collected. + +Example when the nodes are receiving data over a DPDK interface: +Enable tracing using "trace add dpdk-input 20" +(or other interface xxx-input e.g. af-packet-input, tapcli-rx etc) and +execute "show trace" to view the IOAM data collected: + + + vpp# trace add dpdk-input 20 + + vpp# show trace + + ------------------- Start of thread 0 vpp_main ------------------- + + Packet 1 + + 00:00:19:294697: dpdk-input + GigabitEthernetb/0/0 rx queue 0 + buffer 0x10e6b: current data 0, length 214, free-list 0, totlen-nifb 0, trace 0x0 + PKT MBUF: port 0, nb_segs 1, pkt_len 214 + buf_len 2176, data_len 214, ol_flags 0x0, data_off 128, phys_addr 0xe9a35a00 + packet_type 0x0 + IP6: 00:50:56:9c:df:72 -> 00:50:56:9c:be:55 + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + tos 0x00, flow label 0x0, hop limit 63, payload length 160 + 00:00:19:294737: ethernet-input + IP6: 00:50:56:9c:df:72 -> 00:50:56:9c:be:55 + 00:00:19:294753: ip6-input + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + tos 0x00, flow label 0x0, hop limit 63, payload length 160 + 00:00:19:294757: ip6-lookup + fib 0 adj-idx 15 : indirect via db05::2 flow hash: 0x00000000 + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + tos 0x00, flow label 0x0, hop limit 63, payload length 160 + 00:00:19:294802: ip6-hop-by-hop + IP6_HOP_BY_HOP: next index 5 len 96 traced 96 Trace Type 0x1f , 1 elts left + [0] ttl 0x0 node ID 0x0 ingress 0x0 egress 0x0 ts 0x0 + app 0x0 + [1] ttl 0x3e node ID 0x3 ingress 0x1 egress 0x2 ts 0xb68c2213 + app 0x1234 + buffer 0x10e6b: current data 0, length 214, free-list 0, totlen-nifb 0, trace 0x0 + PKT MBUF: port 0, nb_segs 1, pkt_len 214 + buf_len 2176, data_len 214, ol_flags 0x0, data_off 128, phys_addr 0xe9a35a00 + packet_type 0x0 + IP6: 00:50:56:9c:df:72 -> 00:50:56:9c:be:55 + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + tos 0x00, flow label 0x0, hop limit 63, payload length 160 + 00:00:19:294737: ethernet-input + IP6: 00:50:56:9c:df:72 -> 00:50:56:9c:be:55 + 00:00:19:294753: ip6-input + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + tos 0x00, flow label 0x0, hop limit 63, payload length 160 + 00:00:19:294757: ip6-lookup + fib 0 adj-idx 15 : indirect via db05::2 flow hash: 0x00000000 + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + tos 0x00, flow label 0x0, hop limit 63, payload length 160 + 00:00:19:294802: ip6-hop-by-hop + IP6_HOP_BY_HOP: next index 5 len 96 traced 96 Trace Type 0x1f , 1 elts left + [0] ttl 0x0 node ID 0x0 ingress 0x0 egress 0x0 ts 0x0 + app 0x0 + [1] ttl 0x3e node ID 0x3 ingress 0x1 egress 0x2 ts 0xb68c2213 + app 0x1234 + [2] ttl 0x3f node ID 0x2 ingress 0x1 egress 0x2 ts 0xb68c2204 + app 0x1234 + [3] ttl 0x40 node ID 0x1 ingress 0x5 egress 0x6 ts 0xb68c2200 + app 0x1234 + POT opt present + random = 0x577a916946071950, Cumulative = 0x10b46e78a35a392d, Index = 0x0 + 00:00:19:294810: ip6-rewrite + tx_sw_if_index 1 adj-idx 14 : GigabitEthernetb/0/0 + IP6: 00:50:56:9c:be:55 -> 00:50:56:9c:df:72 flow hash: 0x00000000 + IP6: 00:50:56:9c:be:55 -> 00:50:56:9c:df:72 + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + tos 0x00, flow label 0x0, hop limit 62, payload length 160 + 00:00:19:294814: GigabitEthernetb/0/0-output + GigabitEthernetb/0/0 + IP6: 00:50:56:9c:be:55 -> 00:50:56:9c:df:72 + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + tos 0x00, flow label 0x0, hop limit 62, payload length 160 + 00:00:19:294820: GigabitEthernetb/0/0-tx + GigabitEthernetb/0/0 tx queue 0 + buffer 0x10e6b: current data 0, length 214, free-list 0, totlen-nifb 0, trace 0x0 + IP6: 00:50:56:9c:be:55 -> 00:50:56:9c:df:72 + + IP6_HOP_BY_HOP_OPTIONS: db05::2 -> db06::6 + + tos 0x00, flow label 0x0, hop limit 62, payload length 160 + |