1 files changed, 0 insertions, 74 deletions
diff --git a/src/vnet/ipsec-gre/ipsec_gre_doc.md b/src/vnet/ipsec-gre/ipsec_gre_doc.md
deleted file mode 100644
index e1bb9cdab1a..00000000000
--- a/src/vnet/ipsec-gre/ipsec_gre_doc.md
+++ /dev/null
@@ -1,74 +0,0 @@
-# VPP L2-GRE over IPsec implementation    {#ipsec_gre_doc}
-
-This is a memo intended to contain documentation of the VPP L2-GRE over IPsec implementation.
-Everything that is not directly obvious should come here.
-
-
-## L2-GRE over IPsec
-GRE encapsulate layer 2 traffic and IPSec encrypt what is encapsulated by GRE. The whole point of L2-GRE over IPSec is to tunnel layer 2 over GRE and IPSec by bridging the physical interface with IPSec-GRE tunnel interface.
-
-There are 2 dedicated nodes for encapsulation:
-* ipsec-gre<n>-tx - add GRE header
-* esp-encrypt - encrypt GRE packet to ESP packet
-
-There are 3 dedicated nodes for decapsulation:
-* ipsec-if-input - match IPSec SA by source IP address and SPI in ESP packet
-* esp-decrypt - decrypt ESP packet
-* ipsec-gre-input - remove GRE header
-
-
-### Configuration
-
-L2-GRE over IPsec support the following CLI configuration command:
-    create ipsec gre tunnel src <addr> dst <addr> local-sa <id> remote-sa <id> [del]
-
-src: tunnel source IPv4 address
-dst: tunnel destination IPv4 address
-local-sa: tunnel local IPSec Security Association
-remote-sa: tunnel remote IPSec Security Association
-del: delete IPSec-GRE tunnel
-
-L2-GRE over IPsec support the following API configuration command:
-    ipsec_gre_add_del_tunnel src <addr> dst <addr> local_sa <sa-id> remote_sa <sa-id> [del]
-
-src: tunnel source IPv4 address
-dst: tunnel destination IPv4 address
-local_sa: tunnel local IPSec Security Association
-remote_sa: tunnel remote IPSec Security Association
-del: delete IPSec-GRE tunnel
-
-
-### Configuration example
-
-Interface GigabitEthernet0/9/0 is in bridge with ipsec-gre0 tunnel interface, interface GigabitEthernet0/8/0 sending encapsulated and encrypted traffic.
-
-Configure IPv4 address on sending interface:
-set int ip address GigabitEthernet0/8/0 192.168.1.1/24
-
-Configure IPSec Security Associations:
-ipsec sa add 10 spi 1001 esp crypto-key 4a506a794f574265564551694d653768 crypto-alg aes-cbc-128 integ-key 4339314b55523947594d6d3547666b45764e6a58 integ-alg sha1-96
-ipsec sa add 20 spi 1000 esp crypto-key 49517065716d6235726c734a4372466c crypto-alg aes-cbc-128 integ-key 307439636a5542735133595835546f68534e4f64 integ-alg sha1-96
-
-Create IPSec-GRE tunnel:
-create ipsec gre tunnel src 192.168.1.1 dst 192.168.1.2 local-sa 10 remote-sa 20
-
-Set interfaces state:
-set int state GigabitEthernet0/8/0 up
-set int state GigabitEthernet0/9/0 up
-set int state ipsec-gre0 up
-
-Bridge physical interface with IPSec-GRE tunnel interface:
-set interface l2 bridge GigabitEthernet0/9/0 1
-set interface l2 bridge ipsec-gre0 1
-
-
-### Operational data
-
-L2-GRE over IPsec support the following CLI show command:
-    show ipsec gre tunnel
-
-L2-GRE over IPsec support the following API dump command:
-    ipsec_gre_tunnel_dump [sw_if_index <nn>]
-
-sw_if_index: software interface index of the IPSec-GRE tunnel interface
-