Age | Commit message (Collapse) | Author | Files | Lines |
|
Change-Id: I9d1d02ffbb3cdbe8c4a3f335ece40f3dcbd848a7
Signed-off-by: Billy McFall <bmcfall@redhat.com>
|
|
Note that the new way to provision MPLSoGRE is using the "normal"
GRE tunnel such as in the following example:
create gre tunnel src 10.0.3.1 dst 10.0.3.3
set in state gre0 up
set int ip addr gre0 10.0.4.1/30
set int mpls gre0 enable
ip route table 4 6.0.0.0/24 via 10.0.4.2 gre0 out-label 30
mpls local-label add 30 eos ip4-lookup-in-table 4
The previous CLIs/APIs used to configure MPLSoGRE tunnel such as
"create mpls gre tunnel...", "mpls encap|decap add label .." and
"show mpls tunnel", etc. can not be used. They will be deprecated
in a later update to the VPP code base.
Change-Id: I244916841924dc2b87d2143691cd8476716c06b1
Signed-off-by: John Lo <loj@cisco.com>
|
|
gcc6 reports:
vpp/oam/oam.c:560:531: error: self-comparison always evaluates to true
[-Werror=tautological-compare]
Change-Id: I7a086099c14c6661d0c6b4cf0370631fc06bc23d
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: I9c23ddbbd576e8c900ba82425572ed7a3c4f56e3
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Fixed Coverity complaining about the clib_memcpy used in
/vnet/vnet/interface.c
Change-Id: I401f05aea1066d829abac1555021e1180b4a161e
Signed-off-by: Pavel Kotucek <pkotucek@cisco.com>
|
|
Change-Id: Id17fcb9154c5337908f29b7ce3a282b6a4b72d64
Signed-off-by: Billy McFall <bmcfall@redhat.com>
|
|
Change-Id: I003f95db85ce5085045c607f0b1daaefa792c910
Signed-off-by: Billy McFall <bmcfall@redhat.com>
|
|
Change-Id: If4c47b91e949483675cf569cd474b6c85fecef05
Signed-off-by: Billy McFall <bmcfall@redhat.com>
|
|
Change the adjacency completion model to pull not push.
A complete adjacency has a rewirte string, an incomplete one does not. the re-write string for a peer comes either from a discovery protocol (i.e. ARP/ND) or can be directly derived from the link type (i.e. GRE tunnels). Which method it is, is interface type specific.
For each packet type sent on a link to a peer there is a corresponding adjacency. For example, if there is a peer 10.0.0.1 on Eth0 and we need to send to it IPv4 and MPLS packets, there will be two adjacencies; one for the IPv4 and one for the MPLS packets. The adjacencies are thus distinguished by the packets the carry, this is known as the adjacency's 'link-type'. It is not an L3 packet type, since the adjacency can have a link type of Ethernet (for L2 over GRE).
The discovery protocols are not aware of all the link types required - only the FIB is. the FIB will create adjacencies as and when they are required, and it is thus then desirable to 'pull' from the discovery protocol the re-write required. The alternative (that we have now) is that the discovery protocol pushes (i.e. creates) adjacencies for each link type - this creates more adjacencies than we need.
To pull, FIB now requests from the interface-type to 'complete' the adjacency. The interface can then delegate to the discovery protocol (on ethernet links) or directly build the re-write (i.e on GRE).
Change-Id: I61451789ae03f26b1012d8d6524007b769b6c6ee
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I1c4ec4dd02ce5a16e33aa0908a606496ad0d64cc
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
Useful when attempting to serialize potentially very large data
structures and send them to API clients. NULL pointer checks are
MANDATORY when calling xxx_or_null(...) variant functions.
Change-Id: I6ae272deb7150a2c5aa82ec45a206e5bddee7a02
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
Change-Id: Idf68266f705b0455e5ab0ac73d23c7e0f4120d5b
Signed-off-by: Dave Barach <dave@barachs.net>
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: I5177d6d3349384beb551b4f2f52b30b044ce335b
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
Change-Id: Ie1be9dc057d07c250852952ea159ed3c44c25f5f
Signed-off-by: Billy McFall <bmcfall@redhat.com>
|
|
QEMU 2.7 introduces reconnect support. However it doesn't send
last state of last_avail_idx in the SET_VRING_BASE.
With this patch we are overriding SET_VRING_BASE with value taken
from used->idx.
It is a bit hackish as it basically overrides SET_VRING_BASE
provided value but it should work in most of the cases.
This is what author of reconnect code is also suggesting in his post:
https://lists.gnu.org/archive/html/qemu-devel/2016-06/msg01495.html
Change-Id: I10e5f401c409d2989bf6c43eaea377800a9c76df
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: Idabf89bd27ee95769da16331a6bd1439497b2765
Signed-off-by: Matus Fabian <matfabia@cisco.com>
|
|
Delete operation for SNAT addresses
Dump API for SNAT addresses
Change-Id: I84e888d20286ec2523fbd4ca7e68e3eef5927984
Signed-off-by: Matus Fabian <matfabia@cisco.com>
|
|
Change-Id: I570f57218293a4824f83b38575eacdbe3da540d8
Signed-off-by: Matus Fabian <matfabia@cisco.com>
|
|
Proper cpu pinning in vpp_lite platform, like in normal vpp image.
Extended “show threads” command to show propper information.
Changed handling of coreID and socketID for threads in "show threads"
CLI, pthread_getaffinity is used instead of info stored in DPDK.
Change-Id: Ic8299ec5e284472bb10a37a95fadeed57b6edae8
Signed-off-by: Pavel Kotucek <pkotucek@cisco.com>
|
|
Change-Id: I7a14d9a28514cdb49f65fab1b120b53239fed7e3
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
The classifier was written with the assumption that next-indicies
of IP4 and IP6 IP_LOOKUP_NEXT nodes are equal. That's not true,
and this patch splits the classifier session for IP4 and IP6.
Change-Id: Id0368f17bb1d3f145b771d2dc283b56871264e99
Signed-off-by: Ole Troan <ot@cisco.com>
|
|
Change-Id: Ie221e246dd8c6a1b3c76e7aa85924762d4397782
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: Ieea56f3bf9e749878d9f2b35d39d9f7a9cdabde4
Signed-off-by: Filip Tehlar <ftehlar@cisco.com>
|
|
Eliminate an unused parameter in vnet_feature_arc_init(...) which
eliminates a spurious relationship between feature arcs and ip.
Add doxygen tags for 2x debug CLI commands, and for
vnet_feature_arc_init(...)
Change-Id: If83589539bcbbbd4d85e84458dd7eb7eb08837a0
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
This reverts commit 822af5c95d080a58cda504228df4b5f3896e72b6.
Reason for revert is a bug in procps upstart script.
Change-Id: Ie9e501c9b52e65d8d0f31ce6600823021e89fb6f
Signed-off-by: Miroslav Miklus <mmiklus@cisco.com>
|
|
xxhash calculation takes 10 clock cycles on Haswell so it makes sense
to use crc32q insutrction when available.
Change-Id: Iab5e7d9c8ec0125626bbcd067e5dc30574c8febc
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: Icb0ce47134146c3a212b234f088c682982480128
Signed-off-by: Peter Ginchev <pginchev@cisco.com>
|
|
This adds a basic test for the four existing encap modes
for the load balancer plugin.
- ip4 over gre4
- ip4 over gre6
- ip6 over gre4
- ip6 over gre6
Apparently, scapy does not support GRE and IPv6 combinations.
Hence, those tests do send packets through VPP, but only
ip4 over gre4 output is actually parsed and verified.
Change-Id: I7cedb0f88fd0788ee51b1428ddf9cff7c037511f
Signed-off-by: Pierre Pfister <ppfister@cisco.com>
|
|
Change-Id: Iff32c488af9b71acbc4e572c6741afae0a67333c
Signed-off-by: Juraj Sloboda <jsloboda@cisco.com>
|
|
In order to have meaningfull IPFIX implementation we should be able
to classify all packets flowing through vpp. But existing IPv4 and IPv6
classifier nodes are called only if destination IP address is local
to vpp. This commit adds new IPv4 and IPv6 classifier nodes that should
be used for collecting flow statistics.
Change-Id: I60e60105663ba15b5200862a23bb817047fe4d1a
Signed-off-by: Juraj Sloboda <jsloboda@cisco.com>
|
|
Please send SIGTERM to stop vpp_api_test, especially during
long-running operations such as a high-count asynchronous set of
ip_add_del_routes.
Otherwise, there's every chance that the data plane to vpp_api_test
message queue will fill and cause an easily-avoided deadlock.
Change-Id: I09309b445c354e1a692fed708dd5ea44d1ea9882
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
Added more ability to search history to vppctl shell
*Up and down keys give history
*Script now written in Python 2.7.6
*Contains all original functionality
*Added Python dependency for deb/rpms
Change-Id: I5088f7b018fce92b9b5411df0bffc34709810dec
Signed-off-by: Padraig Connolly <padraig.connolly@intel.com>
|
|
some other fixes and enhancemets to address failures in the IPv6 Scale testing:
- The rate at which VPP sends ARP/ND requests, 1 per-millisecond, is too high. This is reduced to 1 every 10 ms. probably still too high.
- If an ARP/ND response is received that does not contain a change to the known MAC address, no further processing is done.
- Added stats to get info about the async FIB walks.
- When walking FIB entries and performing a load-balance update, it is not necessary to re-insert the LB in the forwarding table.
Change-Id: Ifd47e4bdbce94495f44aaf1b78e7d1395ed870d1
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
The api was allocating a vector for the name, passing it, then freeing
it, on create. The cli allocated, passed then forgot about it.
af_packet_create_if was storing a reference to the name, which in the
case of the api, meant it was referencing dead memory. On
af_packet_delete_if this reference was freed, so in the api case, there
was a double free.
Also, the cli for delete leaked the name.
Change-Id: I4d572bd2936eaf8ea7a0a8ff282e83ac2bf1b062
Signed-off-by: Ivan Kelly <ivan@midokura.com>
|
|
Change-Id: I5510a0ae3ecfeb5bd41c3a73e6e05465ebd96165
Signed-off-by: Marek Gradzki <mgradzki@cisco.com>
Signed-off-by: Maros Marsalek <mmarsale@cisco.com>
|
|
This patch adds plugin path to vpp commandline arguments
when 'make test' is run.
Hence, test cases can test plugins.
Change-Id: Ib90efa1f62e03b45b84533c49c7a5d040aa8cddf
Signed-off-by: Pierre Pfister <ppfister@cisco.com>
|
|
In a heirarchical FIB performing a unicast RPF check would require the traversal of the data-plane graph to seek out all the adjacency objects and then read those to find their interface. This is not efficient. Instead, for each path-list we construct a list of unique input interfaces and link this uRPF-list against the entry in the prefix table. In the data-plane the uRPF list can be retrieved from the load-balance lookup result and the RPF check is a simple and efficient walk across the minimal interface list. The uRPF-list is maintained as the routing heirarchy changes, in a similar way to the data-plane object graph.
We also provide a knob to allow an arbitrary prefix to pass the loose check.
Change-Id: Ie7c0ae3c4483ef467cfd5b136ee0315ff98ec15b
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Uses existing UDP local API in order to register
requested UDP port punt to the host.
CLI: set punt udp [del] <port>
API: punt protocol <l4-protocol> [ip <ver>] [port <l4-port>] [del]
* Only UDP (l4-protocol = 17) is supported at this time
Change-Id: I9232af1c891d1ed174d77f3e0dfe60c4b9d85e40
Signed-off-by: Alex Popovsky <apopovsk@cisco.com>
|
|
Change-Id: Ife7b2907012a79e6893cfa7f2cf61c7a54865248
Signed-off-by: Pavel Kotucek <pkotucek@cisco.com>
|
|
Change-Id: Ic29592d39f1d672cb6e7e32b4af6123683e022a7
Signed-off-by: Matus Fabian <matfabia@cisco.com>
|
|
Change-Id: Ic7ae9b43020ab4d26214bfab71b19ee259771c52
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Move check for link-local source IP address for MAC/IP notification
only. Allow generation of response to IP6 ND solicitation request
if a match is found for target IP irrespective of source IP type.
Change-Id: Ib79d4b75fb4fe8aece625fd8cd26c8b9fc75ea47
Signed-off-by: John Lo <loj@cisco.com>
|
|
ip[4|6]_sw_interface_enable_disable() should be called for
the unnumbered interface (and not on the interface with IP address)
Change-Id: Iffd347c539567c1302fa8136eea9c4e06b24d1bd
Signed-off-by: Igor Mikhailov (imichail) <imichail@cisco.com>
|
|
Change-Id: Ib67bf1a898e3c1e4038698f1cb068ae9099d7921
Signed-off-by: Klement Sekera <ksekera@cisco.com>
|
|
Change-Id: Ice0a6939b399eed150b0c58139b79dd4bed91113
Signed-off-by: Vengada Govindan <venggovi@cisco.com>
|
|
Change-Id: I2cc57079741279669241b88d0317853e1312e8c5
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
1:1 NAT
1:1 NAT with ports
1:1 NAT static mapping only - add "static mapping only [connection tracking]"
to snat startup config
Change-Id: I37cd06a9d71d1943eb6618034d7c547c4a9348c4
Signed-off-by: Matus Fabian <matfabia@cisco.com>
|
|
Recheck.
This is to support multiple VPP instances on same host.
Change-Id: Ibe511b1f790fc8771900085577423f7e71dc45df
Signed-off-by: Ole Troan <ot@cisco.com>
|
|
This patch fixes load balancer, which was not working
since FIB 2.0.
Two FIB DPO types are defined:
- One for IPv4 GRE
- One for IPv6 GRE
When an AS is created, the plugin automatically uses
the result from the FIB in order to transmit the packet.
Therefore, the packet does not need to visit ip-lookup twice.
The 'bypass' command was removed, as it is now done
automatically using this process.
Change-Id: Ib505ba31bfc67897eaff752821087821c360360a
Signed-off-by: Pierre Pfister <ppfister@cisco.com>
|
|
Change-Id: Ibbcce6f54bc76b8922b1c649278643c6294d13f9
Signed-off-by: Damjan Marion <damarion@cisco.com>
|