Age | Commit message (Collapse) | Author | Files | Lines |
|
DPDK 18.08 verifies if all set bits are supported and fails if not....
Change-Id: Ia87242fcda11147dff3bebe2e2bef32f0a8891fb
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: If1b93341c222160b9a08f127620c024620e55c37
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Fix a typo from previous patch. Change 0x104 to 0x1004.
Change-Id: I82230a8a0ec01567eb1d4bc12ac02062c2a98347
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
If a PMD writes too many log messages using rte_vlog(), the
pipe for logging can fill and then rte_vlog() will block
on fflush() while it waits for something to read from the other
side of the pipe. That will never happen since the process node
that would read the other side of the pipe runs in the
same thread.
Set the write fd to non-blocking before the call to
rte_openlog_stream(). If the pipe is full, calls to write() or
fflush() will fail but execution will continue.
Change-Id: I0e5d710629633acda5617ff29897d6582c255d57
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
Recognize the PF and VF device IDs for the Mellanox adapter
used on Azure.
Change-Id: Ic7b36b37ac93db2b696354ffe6fa2b6d62ee3801
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
This patch addresses the coverity scan warnings reported for the DPDK
plugin.
Change-Id: Ie7ac7ffcf4a6c63245eae0f9910a193ab1e318a8
Signed-off-by: Marco Varlese <marco.varlese@suse.de>
|
|
The driver implements Cavium QLogic FastLinQ QL4xxxx 10G/25G/40G/50G/100G
Intelligent Ethernet Adapters (IEA) and Converged Network Adapters (CNA)
(doc/guides/nics/qede.rst)
Change-Id: If17e8cb572eb8c0585085be1c7cfdfa159eb6e68
Signed-off-by: Igor Mikhailov (imichail) <imichail@cisco.com>
|
|
Change-Id: If4da80c7eefe55905594eaaba0946d75f0892da5
Signed-off-by: Igor Mikhailov (imichail) <imichail@cisco.com>
|
|
Change-Id: I7c611d3fa7fabe82294fc22a61d5a3927a2da39d
Signed-off-by: Jessica Tallon <tsyesika@igalia.com>
|
|
Workaround for lack of driver interrupt support. Also quite handy for
home gateway, laptop/vagrant, other use-cases not requiring maximum
vectors/second for proper operation.
Change-Id: Ifc4b98112450664beef67b89ab8a6940a3bf24b5
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
Change-Id: I23caebf602e3e6ff45fdec106a0da88f6de7a284
Signed-off-by: Igor Mikhailov (imichail) <imichail@cisco.com>
|
|
Change-Id: Iee8de25ab3c68ae3698c79852195dc336050914c
Signed-off-by: Ole Troan <ot@cisco.com>
|
|
This patch separates setting of hardware interfaec and software
interface MTU. Software MTU is L2 payload MTU (i.e. not including L2
header). Per-protocol MTU for IPv4, IPv6 and MPLS can also be set.
Currently only IP4, IP6 are enabled in adjacency / rewrite code.
Documentation in src/vnet/MTU.md
Change-Id: Iee2fd6f0bbc8210748dd8e073ab9fab87d323690
Signed-off-by: Ole Troan <ot@cisco.com>
|
|
... introduced with dpdk 18.05 support patch
Change-Id: Idf2283888f81d7652599651c0d65476e451f9343
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Added code to initialize failsafe PMD
This is part of initial effort to enable vpp running over
dpdk on failsafe PMD in Microsoft Azure(4/4).
Change-Id: Ia2469c7087ca4b5c7881dfb11ec5c4fcebaa1d04
Signed-off-by: Rui Cai <rucai@microsoft.com>
|
|
Change-Id: I205932bc727c990011bbbe1dc6c0cf5349d19806
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Added configure argument "--with-log2-cache-line-bytes=5|6|7|auto"
AKA 32, 64, or 128 bytes, or use the inferred value from the build host.
produces build-xxx/vpp/vppinfra/config.h, which .../src/vppinfra/cache.h
Kernels which implement the following pseudo-file (aka x86_64) are
easy: /sys/devices/system/cpu/cpu0/cache/index0/coherency_line_size
Otherwise, extract the cpuid from /proc/cpuinfo and map it to the
cache line size.
Change-Id: I7ff861e042faf82c3901fa1db98864fbdea95b74
Signed-off-by: Dave Barach <dave@barachs.net>
Signed-off-by: Nitin Saxena <nitin.saxena@cavium.com>
|
|
Prior to the change, dpdk plugin assumes xd->device_index is
used both as index for internal dpdk_main->devices array
and DPDK port index to call into DPDK APIs.
However, when running on top of Failsafe PMDs,
DPDK port index range may no longer be contiguous (as noted:
http://dpdk.org/ml/archives/dev/2018-March/092375.html
for related changes in DPDK). Because this, dpdk plugin can
no longer iterate through all available DPDK ports
with a for 0->rte_eth_dev_count() loop and the assumption of
device_index no longer holds.
This is part of initial effort to enable vpp running over
dpdk on failsafe PMD in Microsoft Azure(3/4).
Change-Id: I416fd80f2d40e12e139f8f3492814da98343eae7
Signed-off-by: Rui Cai <rucai@microsoft.com>
|
|
This fixes some compilation warnings with clang on AArch64.
Change-Id: Idb941944e3f199f483c80e143a9e5163a031c4aa
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
port_id be used for dpdk port_id
Change-Id: Ia7d8cdc5dec2ad658c11f9c0f3ef8005a470ac3c
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
1、Adding PMD type for support Cavium LiquidIO II CN23XX NIC;
2、Our company is using VPP + DPDK +Cavium LiquidIO II CN23XX NIC,
Unfortunately, the latest VPP code does not support
Cavium LiquidIO II CN23XX pci.
So I increased the PMD type to support LiquidIO NIC,
and can run normally, we most subsequent projects are
based on VPP + DPDK + Cavium LiquidIO II CN23XX NIC model,
so I hope VPP team can adopt this requirement, thanks a lot.
Change-Id: I604ae444d69b37c2e26962bfe4ccdfe983b75041
Signed-off-by: chuhong yao <ych@panath.cn>
|
|
The option no-multi-seg doesn't take effect for RX since MTU
which is too large is passed to DPDK lib, Which causes PMDs
are running XXX_scattered_rx function. The patch fixes the issue.
Change-Id: I91a6fb23fd118e872c8a52a6c35c36a86cb2c02b
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
|
|
when flows are enabled on the device
Change-Id: I971764988d5a9e7078468f627205b3fa60736263
Signed-off-by: Eyal Bari <ebari@cisco.com>
|
|
During dpdk_lib_init, it calculates MRU and MTU and later calls
rte_eth_dev_set_mtu with calculated MTU value. However, dpdk_device_setup
calls rte_eth_dev_set_mtu with hi->max_packet_bytes, which is set to be
MRU value in dpdk_lib_init earlier.
Most of the time, MRU != MTU in dpdk_lib_init and it looks like
hi->max_packet_bytes is treated as MTU in other parts of vpp codebase.
Therefore, dpdk_lib_init should be consistent and use MTU instead of MRU
for hi->max_packet_bytes.
Change-Id: I23ff2a6cd45d6bc819b6f64d5f0fc0490b8a44de
Signed-off-by: Rui Cai <rucai@microsoft.com>
|
|
When port_type_from_speed_capa() is called before the port link update isn't completed,
xd->port_type becomes VNET_DPDK_PORT_TYPE_UNKNOWN. This happens with Mellanox NIC
without lsc interrupt. Calling rte_eth_link_get before getting dev_info will ensure
the link state is up-to-date.
Change-Id: I83a59654778eb4bf0c65a4a4e225a326227b9641
Signed-off-by: Steve Shin <jonshin@cisco.com>
|
|
Change-Id: Ibea4a96bdec5e368301a03d8b11a0712fa0265e0
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: Ifea9c772e8784642433b92091f5769eb9ec06890
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: If174d189de40e6f9ffae99997bba93a2519d9fda
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
- use of vlib_log for non-dataplane logging
- redirect of dpdk logs trough unix pipe into vlib_log
- "show dpdk physmem" cli
Change-Id: I5da70f9c130273072a8cc80d169df31fc216b2c2
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
https://gerrit.fd.io/r/#/c/7701/ accidentally removed 3 lines of code in
dpdk/device/init.c which were added by https://gerrit.fd.io/r/#/c/7826/
case VNET_DPDK_PMD_VHOST_ETHER:
xd->port_type = VNET_DPDK_PORT_TYPE_VHOST_ETHER;
break;
Those lines were needed to recognize vhost-user interface which is created
via vdev command in dpdk and display VhostEthernet. Without them,
UnknownEthernet is displayed.
Change-Id: I6d7ee6aecc6a415fbb7308595d515649475bcd5f
Signed-off-by: Steven <sluong@cisco.com>
|
|
interface)"
This reverts commit 70083ee74c3141bbefb185525315f1b34497dcaa.
Reverting as this patch is causing following crash:
0: /home/damarion/cisco/vpp3/build-data/../src/vnet/devices/devices.h:131 (vnet_get_device_input_thread_index) assertion `queue_id < vec_len (hw->input_node_thread_index_by_queue)' fails
Aborted
Change-Id: Ie2a365032110b1f67be7a9d832885b9899813d39
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: I98bd454a761a1032738a21edeb0fe847e801f901
Signed-off-by: Ole Troan <ot@cisco.com>
|
|
Change-Id: Iacb32e6e855f7b77108154d956ef27ee141bbde0
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
Linux kernel and DPDK recognize the following Ethernet speeds:
10M, 100M, 1G, 2.5G, 5G, 10G, 20G, 25G, 40G, 50G, 56G and 100G.
Add consistent Ethernet speeds to VPP.
Change-Id: I4cfcf378fb34425c1206db5aa2f6bdcc66e0a6ab
Signed-off-by: Lee Roberts <lee.roberts@hpe.com>
|
|
Change-Id: I1d3ede2b043e1fd4abc54f540bb1d3ac9863016e
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
ENA doesn't support scatter-gather. The PMD started
failing rte_eth_dev_rx_queue_config() in DPDK 18.02
if the flag to enable it is set. Turn the flag off in
dpdk_lib_init().
Change-Id: Ifdd9f188c89b46efe82412c75fb935a92436da1c
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
Problem: rte_eth_dev_set_mtu() returns with failure from ThunderX NICVF
DPDK PMD driver which supports MTU less than ETHERNET_MAX_PACKET_BYTES.
rte_eth_dev_set_mtu() being called twice from dpdk_lib_init(): one via
dpdk_device_setup() and second in dpdk_lib_init() itself. Currently
dpdk_lib_init() passes vnet_hardware_interface->max_packet_bytes as an
argument to rte_eth_dev_set_mtu() without consulting dev_info.max_rx_pktlen.
NICs like i4oe, ixgbe can support MTU much greater than 9216 hence its not
a problem for those NICS.
Fix: This patch calculates dpdk_device->port_conf.rxmode.max_rx_pkt_len,
vnet_hardware_interface->max_packet_bytes and MTU by consulting
dev_info.max_rx_pktlen.
Change-Id: If04bbfae49ee971dac0063ff1835e4a9c3087865
Signed-off-by: Nitin Saxena <nitin.saxena@cavium.com>
|
|
Change-Id: Icd2184dec16d30cdcc689ca37c834b5df2f0a1a3
Signed-off-by: Eyal Bari <ebari@cisco.com>
|
|
Change-Id: I853386aebfe488ebb10328435b81b6e3403c5dd0
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: I1699e440052faa317b06d46692e8656a41d21bfe
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: Ib4012ff598698924484525932d041988cc4c63f6
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Elastic Network Adapter PMD for newer AWS instance types
Change-Id: Ic7f6ac4a261ccc7af3ffb2ed8950274532e3feae
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
Also fixes old ixge driver, so it works with recent physmem changes and
vfio.
Change-Id: Id4be74b34daed47cd281a77eec43d6692340d882
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
unify code from both branches
Change-Id: Iae7325cff8c799c7827727ad7465bec089e39f50
Signed-off-by: Eyal Bari <ebari@cisco.com>
|
|
Change-Id: I31d2cbb02a0f59603ef1adc0d185e3d775dfda2f
Signed-off-by: Eyal Bari <ebari@cisco.com>
|
|
Change-Id: Ic43c70bfe3e93cb3e6cfab7cda1986e44e371c06
Signed-off-by: Eyal Bari <ebari@cisco.com>
|
|
Add legacy and modern macros to pci_config header.
This follows dpdk commit: 4c7903658f6b5a8f4901224ef405445541b91e4a
And PCI Device Conformance doc :
docs.oasis-open.org/virtio/virtio/v1.0/cs02/virtio-v1.0-cs02.html#x1-640001
Change-Id: Iacd40ea8c06f220736ca0bc7ce68bcf1e55b68f6
Signed-off-by: Gabriel Ganne <gabriel.ganne@enea.com>
|
|
Change-Id: I3713b4c460a3cd414b560e16aac054aee2e1181b
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
New startup.conf knob:
dpdk { ... no-tx-checksum-offload ... }
Change-Id: I337fd57616dd77687300861b411b420a3cb75149
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: I0a6d1257e391c3b6f7da6498bd5f7d4c545d17e9
Signed-off-by: Damjan Marion <damarion@cisco.com>
|