| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Change-Id: I0fb646c350b392d69658ba4188ae25e0f0a6cdc1
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
|
|
Create lacp-process when the very first slave interface is added to the bond.
Log an event message when lacp-process starts/stops.
Be mindful when lacp-process is signalled to stop.
Type: refactor
Change-Id: I79e10e0a2a385a21a52ae5b8735f24631fdba293
Signed-off-by: Steven Luong <sluong@cisco.com>
|
|
- Make plugin descriptions more consistent
so the output of "show plugin" can be
used in the wiki.
Change-Id: I4c6feb11e7dcc5a4cf0848eed37f1d3b035c7dda
Signed-off-by: Dave Wallace <dwallacelf@gmail.com>
|
|
By definition, passive mode means the node does not start sending lacp pdu until
it first hears from the partner or remote.
- Rename ptx machine's BEGIN state to NO_PERIODIC state.
- Put periodic machine in NO_PERIDOIC state when the interface is enabled for
lacp. ptx machine will transition out of NO_PERIODIC state when the local node
hears from the remote or when the local node is configured for active mode.
- Also add send and receive statistics for debugging.
Change-Id: I747953b9595ed31328b2f4f3e7a8d15d01e04d7f
Signed-off-by: Steven Luong <sluong@cisco.com>
|
|
Change-Id: Ied34720ca5a6e6e717eea4e86003e854031b6eab
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
When the slave interface is admin up after it is added to the bond group,
lacp does not send lacp pdu's to the interface because its periodic timer
is not running.
The issue was the slave interface's variables got reset after the state
machines were initialized.
Change-Id: I2942556ce29a4acc97db3be40293e69bed7b6679
Signed-off-by: Steven <sluong@cisco.com>
|
|
[VPP-1251]
Problem:
When the bond subinterface is removed, it was observed that we lost the lacp
partner. Show hardware shows rx counter goes up, but show interface does not
for the slave interfaces.
Cause:
We reset the interface promiscuous mode when the bond subinterface is deleted.
This causes dpdk not to accept any packet. Leave the interface in promiscuous
mode fixes the problem.
Other fixes:
There are few places we use hw_if_index as if they are sw_if_index. But they
don't necessarily have the same value. As soon as a subinterface is created,
they start to diverge. The fix is to use the correct API for the hw_if_index
and sw_if_index.
Change-Id: I1e6b8bca0a4aae396d217a141271cbf968500c91
Signed-off-by: Steven <sluong@cisco.com>
(cherry picked from commit 42c6599bf3057a7e8f4f00f5b6a9dd72af48d283)
|
|
Do fast-rate if we are not yet synchronized with the partner.
Stop sending LACP updates as a flash in the worker thread. Just expire the
timer and let the lacp_process handle sending LACP PDU.
Change-Id: I8b36fe74e752e7f45bd4a8d70512c0341cc197a1
Signed-off-by: Steven <sluong@cisco.com>
|
|
Add bonding driver to support creation of bond interface which composes of
multiple slave interfaces. The slave interfaces could be physical interfaces,
or just any virtual interfaces. For example, memif interfaces.
The syntax to create a bond interface is
create bond mode <lacp | xor | acitve-backup | broadcast | round-robin>
To enslave an interface to the bond interface,
enslave interface TenGigabitEthernet6/0/0 to BondEthernet0
Please see src/plugins/lacp/lacp_doc.md for more examples and additional
options.
LACP is a control plane protocol which manages and monitors the status of
the slave interfaces. The protocol is part of 802.3ad standard. This patch
implements LACPv1. LACPv2 is not supported.
To enable LACP on the bond interface, specify "mode lacp" when the bond
interface is created. The syntax to enslave a slave interface is the same as
other bonding modes.
Change-Id: I06581d3b87635972f9f0e1ec50b67560fc13e26c
Signed-off-by: Steven <sluong@cisco.com>
|
Zhiyong Yang
Steven Luong
Dave Wallace
Dave Barach