| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Change-Id: Ibc59323e849810531dd0963e85493efad3b86857
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
When the slave interface is admin up after it is added to the bond group,
lacp does not send lacp pdu's to the interface because its periodic timer
is not running.
The issue was the slave interface's variables got reset after the state
machines were initialized.
Change-Id: I2942556ce29a4acc97db3be40293e69bed7b6679
Signed-off-by: Steven <sluong@cisco.com>
|
|
- hash is great. But it is a bit too slow for the DP. Use direct array indexing
to quickly retrieve the slave interface.
- the algorithm used by flow hash is great. But it is a bit too slow for the DP.
Use l2_hash_hash() extracted from lb_hash.h which ECMP is using. It makes use
of intrinsic crc32 instruction set.
- shortcut modulo arithmetic when the operand is 2**x (where x up to 4) to
avoid division instruction.
- special case for link count == 1 in bond_tx_fn()
- use clib_mem_unaligned to access data for the packet to avoid alignment error
- Fix some typos for packet tracing.
Change-Id: I8eae3ad497061c5473aa675ba894ee0211120d25
Signed-off-by: Steven <sluong@cisco.com>
|
|
[VPP-1251]
Problem:
When the bond subinterface is removed, it was observed that we lost the lacp
partner. Show hardware shows rx counter goes up, but show interface does not
for the slave interfaces.
Cause:
We reset the interface promiscuous mode when the bond subinterface is deleted.
This causes dpdk not to accept any packet. Leave the interface in promiscuous
mode fixes the problem.
Other fixes:
There are few places we use hw_if_index as if they are sw_if_index. But they
don't necessarily have the same value. As soon as a subinterface is created,
they start to diverge. The fix is to use the correct API for the hw_if_index
and sw_if_index.
Change-Id: I1e6b8bca0a4aae396d217a141271cbf968500c91
Signed-off-by: Steven <sluong@cisco.com>
(cherry picked from commit 42c6599bf3057a7e8f4f00f5b6a9dd72af48d283)
|
|
We should be sending LACP PDU every second if the partner has LACP_TIMEOUT flag
set which means it will time us out in 3 seconds.
Add interface name for lacp trace
Change-Id: If7d816c062d03e80cc0dd7d10dba0b76ace0664a
Signed-off-by: Steven <sluong@cisco.com>
|
|
Change-Id: Ibcffee7d20dbb79720199bcd82d2353f39d5544f
Signed-off-by: Chris Luke <chrisy@flirble.org>
|
|
Do fast-rate if we are not yet synchronized with the partner.
Stop sending LACP updates as a flash in the worker thread. Just expire the
timer and let the lacp_process handle sending LACP PDU.
Change-Id: I8b36fe74e752e7f45bd4a8d70512c0341cc197a1
Signed-off-by: Steven <sluong@cisco.com>
|
|
Add bonding driver to support creation of bond interface which composes of
multiple slave interfaces. The slave interfaces could be physical interfaces,
or just any virtual interfaces. For example, memif interfaces.
The syntax to create a bond interface is
create bond mode <lacp | xor | acitve-backup | broadcast | round-robin>
To enslave an interface to the bond interface,
enslave interface TenGigabitEthernet6/0/0 to BondEthernet0
Please see src/plugins/lacp/lacp_doc.md for more examples and additional
options.
LACP is a control plane protocol which manages and monitors the status of
the slave interfaces. The protocol is part of 802.3ad standard. This patch
implements LACPv1. LACPv2 is not supported.
To enable LACP on the bond interface, specify "mode lacp" when the bond
interface is created. The syntax to enslave a slave interface is the same as
other bonding modes.
Change-Id: I06581d3b87635972f9f0e1ec50b67560fc13e26c
Signed-off-by: Steven <sluong@cisco.com>
|
Damjan Marion
Steven
Chris Luke