| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch enables statistics from the Arm PMUv3 through the perfmon
plugin.
In comparison to using the Linux "perf" tool, it allows obtaining
direct, per node level statistics (rather than per thread). By accessing
the PMU counter registers directly from userspace, we can avoid the
overhead of using a read() system call and get more accurate and fine
grained statistics about the running of individual nodes.
A demo of perfmon on Arm can be found at:
https://asciinema.org/a/egVNN1OF7JEKHYmfl5bpDYxfF
*Important Note*
Perfmon on Arm is dependent on and works only on Linux kernel versions
of v5.17+ as this is when userspace access to Arm perf counters was
included.
On most Arm systems, a maximum of 7 PMU events can be configured at once
- (6x PMU events + 1x CPU_CYCLE counter). If some perf counters are in
use elsewhere by other applications, and there are insufficient counters
remaining to open the bundle, the perf_event_open call will fail
(provided the events are grouped with the group_fd param, which perfmon
currently utilises).
See arm/events.h for a list of PMUv3 events available, although it is
implementation defined whether most events are implemented or not. Only
a small set of 7 events is required to be implemented in Armv8.0, with
some additional events required in later versions. As such, depending on
the implementation, some statistics may not be available. See Arm
Architecture Reference Manual for Armv8-A, D7.10.2 "The PMU event number
space and common events" for more information.
arm/events.c:arm_init() gets information from the sysfs about what
events are implemented on a particular CPU at runtime. Arm's
implementation of the perfmon source callback .bundle_support uses this
information to disable unsupported events in a bundle, or in the case
no events are supported, disable the entire bundle.
Where a particular event in a bundle is not implemented, the statistic
for that event is shown as '-' in the 'show perfmon statistics' cli
output, by disabling the column.
There is additional code in perfmon.c to only open events which are
marked as implemented. Since we're only opening and reading events that
are implemented, some extra logic is required in cli.c to re-align
either perfmon_node_stats_t or perfmon_reading_t with the column
headings configured in each bundle, taking into account disabled
columns.
Userspace access to perf counters is disabled by default, and needs to
be enabled with 'sudo sysctl kernel/perf_user_access=1'.
There is a check built into the Arm event source init function
(arm/events.c:arm_init) to check that userspace reading of perf counters
is enabled in the /proc/sys/kernel/perf_user_access file.
If the above file does not exist, it means the kernel version is
unsupported. Users without a supported kernel will see a warning
message, and no Arm bundles will be registered to use in perfmon.
Enabling/using plugin:
- include the following in startup.conf:
- plugins { plugin perfmon_plugin.so { enable }
- 'show perfmon bundle [verbose]' - show available statistics bundles
- 'perfmon start bundle <bundle-name>' - enable and start logging
- 'perfmon stop' - stop logging
- 'show perfmon statistics' - show output
For a general guide on using and understanding Arm PMUv3 events, see
https://community.arm.com/arm-community-blogs/b/tools-software-ides-blog/posts/arm-neoverse-n1-performance-analysis-methodology
Type: feature
Signed-off-by: Zachary Leaf <zachary.leaf@arm.com>
Tested-by: Jieqiang Wang <jieqiang.wang@arm.com>
Change-Id: I0620fe5b1bbe78842dfb1d0b6a060bb99e777651
|
|
Added a cli to show Linux perf config for a give perfmon bundle. This
makes it easier to format Linux perf commands for next level analysis.
Type: improvement
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
Change-Id: I9adafa7d441b72120390d186e3c8f884b1bc9828
|
|
Allow perfmon bundles to support more than one bundle type, either node
or thread. Only used for topdown bundle for the moment.
Type: improvement
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
Change-Id: Iba3653a4deb39b0a8ee8ad448a7e8f954283ccd8
|
|
This code seems really usefull for reuse in
other plugins, for pretty table formatting
Type: feature
Change-Id: Ib5784a0dfc81b7d5a5d1f5ccdd02072e460a50fb
Signed-off-by: Nathan Skrzypczak <nathan.skrzypczak@gmail.com>
|
|
This patch sorts 'show perfmon bundle' output in alphabetical order.
Type: improvement
Signed-off-by: Zachary Leaf <zachary.leaf@arm.com>
Change-Id: I26b379b5d6766b9f87f9a3a5013ea92b207fb5d4
|
|
Adding support for Linux papi TMAM on Intel Snowridge. Adds the ability to
indicate that a bundle should be thread or node bundle type based on available
cpu features (rdpmc support).
Type: feature
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
Change-Id: Ib871b2644fdb2410fbb580e0d21c3a8e2be13aba
|
|
Revert raw column from the perfmon plugin.
Type: refactor
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
Change-Id: If127f57ee2022cc1c0ea5177f1655a792f195f1d
|
|
Adding perfmon node TMAM support on ICX.
Type: improvement
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
Change-Id: I48a9a9ff6a72efc28eaf0cb11ef39fb62cebb126
|
|
Original set, start, stop, reset, show etc interface was somewhat cumbersome, we
can improve slightly by combining set and start.
Type: improvement
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
Change-Id: I7b865b2c29d2ab32adbd24d7f8a580da6990bb76
|
|
Add perfmon plugin support to output raw counter and timestamps, both
are useful for debug.
Type: improvement
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
Change-Id: Ia5a73d1f05e3464c18991c2346f0ed8b7ef63099
|
|
Type: feature
Change-Id: I2c14f82393d11fc05c6d229f5c58603ab5c0f14d
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
Zachary Leaf
Ray Kinsella
Nathan Skrzypczak
Damjan Marion