summaryrefslogtreecommitdiffstats
path: root/src/vnet/fib/fib_entry.c
AgeCommit message (Collapse)AuthorFilesLines
2017-11-26FIB: store the node type not the function pointer.Neale Ranns1-2/+0
Saves memory at no appreciable performance cost. before: DBGvpp# sh fib mem FIB memory Name Size in-use /allocated totals Entry 80 7 / 150 560/12000 after: DBGvpp# sh fib mem FIB memory Name Size in-use /allocated totals Entry 72 7 / 7 504/504 Change-Id: Ic5d3920ceb57b54260dc9af2078c26484335fef1 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-11-09BIERNeale Ranns1-0/+1
- see draft-ietf-bier-mpls-encapsulation-10 - midpoint, head and tail functions - supported payload protocols; IPv4 and IPv6 only. Change-Id: I59d7363bb6fdfdce8e4016a68a9c8f5a5e5791cb Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-09-13Add a name to the creation of an IP and MPLS tableNeale Ranns1-4/+2
Change-Id: I4b4648831551519b2ffb6f93255d28a4b8726c22 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-09-11FIB table add/delete APINeale Ranns1-2/+13
part 2; - this adds the code to create an IP and MPLS table via the API. - but the enforcement that the table must be created before it is used is still missing, this is so that CSIT can pass. Change-Id: Id124d884ade6cb7da947225200e3bb193454c555 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-08-08L2 over MPLSNeale Ranns1-1/+7
[support for VPWS/VPLS] - switch to using dpo_proto_t rather than fib_protocol_t in fib_paths so that we can describe L2 paths - VLIB nodes to handle pop/push of MPLS labels to L2 Change-Id: Id050d06a11fd2c9c1c81ce5a0654e6c5ae6afa6e Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-07-18FIB path preferenceNeale Ranns1-1/+1
Paths are given a preference, lowest value is 'best'. Only paths that are up are up contribute to fprwarding - that's unchanged. What's new is that of the path's that re up only those that have the best preference contribute. A poor man's primary and backup. It's not true primary/backup function because the FIB must converge before the lower preference paths are used. Change-Id: Ie4453c4a7b1094c6c2b51fe1594b8302103bb68e Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-06-21ARP: ignore non-connected routes and non-interface sources when determing if ↵Neale Ranns1-3/+7
source is connected Change-Id: I39fb0ec44cc322eaa12c0ff0700fc405d3982bfc Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-23ARP/ND entries for the same address on different interfaces (VPP-848)Neale Ranns1-10/+2
there are, intentionally, no validation checks in the ARP/ND code to prevent an ARP/ND entry from being installed for an address that is not local to the interface's sub-net. This is ok, since the adjacency/FIB code is designed to handle this case using the 'refinement' criteria - i.e. only installing a FIB entry for the address if the address 'refines' (i.e. is more specific than) the interface's sub-net. However, the refinement criteria currently operates on the FIB entry's prefix (which is a /32, so on the address) and not on the next-hop in the path. So, enter multiple ARP entries for the same address on different links, and this refinement criteria uses only the last added path, and so will remove the FIB entry should the ARP entries be added in the 'wrong' order. This fix updates the refinement criteria to work on each path of the FIB entry. The entry is installed if one of the paths refines the covers and only paths refining the cover contribute forwarding. Per-path refinement checks are stored in path-extensions. The patch is rather large as path-extension, which were previously used only for out-going MPLS labels, have been generalized. Change-Id: I00be359148cb948c32c52109e832a70537a7920a Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-26IP Flow Hash Config fixesNeale Ranns1-0/+29
- the flow hash config is (and was) cached on the load-balance object so the fib_table_t struct is not used a switch time. Therefore changes to the table's flow hash config need to be propagated to all load-balances and hance all FIB entries in the table. - enable API for setting the IPv6 table flow hash config - use only the hash config in the fib_table_t object and not on the ipX_fib_t - add tests. Change-Id: Ib804c11162c6d4972c764957562c372f663e05d4 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-07MPLS McastNeale Ranns1-7/+40
1 - interface-DPO Used in the Data-plane to change a packet's input interface 2 - MPLS multicast FIB entry Same as a unicast entry but it links to a replicate not a load-balance DPO 3 - Multicast MPLS tunnel Update MPLS tunnels to use a FIB path-list to describe the endpoint[s]. Use the path-list to generate the forwarding chain (DPOs) to link to . 4 - Resolve a path via a local label (of an mLDP LSP) For IP multicast entries to use an LSP in the replication list, we need to decribe the 'resolve-via-label' where the label is that of a multicast LSP. 5 - MPLS disposition path sets RPF-ID For a interface-less LSP (i.e. mLDP not RSVP-TE) at the tail of the LSP we still need to perform an RPF check. An MPLS disposition DPO performs the MPLS pop validation checks and sets the RPF-ID in the packet. 6 - RPF check with per-entry RPF-ID An RPF-ID is used instead of a real interface SW if index in the case the IP traffic arrives from an LSP that does not have an associated interface. Change-Id: Ib92e177be919147bafeb599729abf3d1abc2f4b3 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-06BFD-FIB interactionsNeale Ranns1-16/+34
- single-hop BFD: attach a delegate to the appropriate adjacency - multi-hop BFD [not supported yet]: attach a delegate to the FIB entry. adjacency/fib_entry state tracks the BFD session state. when the state is down the object does not contribute forwarding hence and hence dependent objects will not use it. For example, if a route is ECMP via two adjacencies and one of them is BFD down, then only the other is used to forward (i.e. we don't drop half the traffic). Change-Id: I0ef53e20e73b067001a132cd0a3045408811a822 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-01MTRIE Optimisations 2Neale Ranns1-2/+2
1) 16-8-8 stride. Reduce trie depth walk traded with increased memory in the top PLY. 2) separate the vector of protocol-independent (PI) fib_table_t with the vector of protocol dependent (PD) FIBs. PD FIBs are large structures, we don't want to burn the memory for ech PD type 3) Go straight to the PD FIB in the data-path thus avoiding an indirection through, e.g., a PLY pool. Change-Id: I800d1ed0b2049040d5da95213f3ed6b12bdd78b7 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-02-24FIB: 1) fix pool realloc during prefix export. 2) don't walk off the end of ↵Neale Ranns1-4/+24
the path-extension vector Change-Id: I8bd8f6917ace089edb1f65bd017b478ee198c03f Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-02-20FIB reset leaves residual routes. Wrong API used to remove the routes meant ↵Neale Ranns1-1/+4
the lock count on the entry did not drop to zero Change-Id: I6e2dff8c3c7976fd1c2e4c5258f5dc73123aa9b7 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-01-05FIB memory leaks (VPP-578)Neale Ranns1-0/+1
1) vec_free the fe_srcs of a fib_entry_t when the fib_entry_t is itself reed 2) in the load-balance fixup if a drop path is required add this to a new vector of next-hops 'fixed_nhs'. This vector is managed by the load-balance function. The caller continues to manage its own set. The function is now const implying that the caller is safe to assume the next-hops do not change. Change-Id: I0f29203ee16b9a270f40edf237488fa99ba65320 Signed-off-by: Neale Ranns <nranns@cisco.com> Signed-off-by: Neale Ranns <neale.ranns@cisco.com>
2016-12-28Reorganize source tree to use single autotools instanceDamjan Marion1-0/+1503
Change-Id: I7b51f88292e057c6443b12224486f2d0c9f8ae23 Signed-off-by: Damjan Marion <damarion@cisco.com>