aboutsummaryrefslogtreecommitdiffstats
path: root/src/vnet/fib/fib_path.c
AgeCommit message (Collapse)AuthorFilesLines
2017-11-26FIB: store the node type not the function pointer.Neale Ranns1-2/+0
Saves memory at no appreciable performance cost. before: DBGvpp# sh fib mem FIB memory Name Size in-use /allocated totals Entry 80 7 / 150 560/12000 after: DBGvpp# sh fib mem FIB memory Name Size in-use /allocated totals Entry 72 7 / 7 504/504 Change-Id: Ic5d3920ceb57b54260dc9af2078c26484335fef1 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-11-14Ip6 dump not showing fib table names (VPP-1063)Neale Ranns1-4/+3
Change-Id: Idc7e7c35f17d514589d1264f1d1be664192ee586 Signed-off-by: Neale Ranns <neale.ranns@cisco.com>
2017-11-11MPLS disposition actions at the tail of unicast LSPsNeale Ranns1-1/+12
Change-Id: I8c42e26152f2ed1246f91b789887bfc923418bdf Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-11-09BIERNeale Ranns1-15/+370
- see draft-ietf-bier-mpls-encapsulation-10 - midpoint, head and tail functions - supported payload protocols; IPv4 and IPv6 only. Change-Id: I59d7363bb6fdfdce8e4016a68a9c8f5a5e5791cb Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-11-07UDP Encapsulation.Neale Ranns1-1/+72
A UDP-encap object that particiapates in the FIB graph and contributes DPO to teh output chain. It thereofre resembles a tunnel but without the interface. FIB paths (and henace routes) can then be created to egress through the UDP-encap. Said routes can have MPLS labels, hence this also allows MPLSoUPD. Encap is uni-directional. For decap, one still registers with the UDP port dispatcher. Change-Id: I23bd345523b20789a1de1b02022ea1148ca50797 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-10-25L3 proxy FIB source for container networkingAndrew Yourtchenko1-7/+8
Change-Id: I4164c4c19c8dbfd73e6ddf94a12056325cc093b9 Signed-off-by: Neale Ranns <nranns@cisco.com> Signed-off-by: Andrew Yourtchenko <ayourtch@gmail.com>
2017-10-14Source Lookup progammable via APINeale Ranns1-2/+8
Change-Id: I5d5d4f22b6369d504455a644f73076d772fbcfb4 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-10-05Distributed Virtual Router SupportNeale Ranns1-22/+42
A distributed virtual router works by attmpeting to switch a packet, but on failing to find a local consumer (i.e. the packet is destined to a locally attached host) then the packet is sent unmodified 'upstream' to where the rest of the 'distributed' router is present. When L3 switching a packet this means the L2 header must not be modifed. This patch adds a 'l2-bridge' object to the L3 FIB which re-injects packets from the L3 path back into the L2 path - use with extreme caution. Change-Id: I069724eb45956647d7980cbe40a80a788ee6ee82 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-10-04Dump of deag/lookup routes has is_drop=1 (VPP-995)Neale Ranns1-0/+2
Change-Id: I58772a83e22885a9ea8a7a981d2bcb4b31a050d2 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-08-21PPPoE usses a midchain adjacency stack on an interface-tx DPONeale Ranns1-7/+7
1) introduce an interface-tx DPO. This is a simple wrapper around a sw_if_index. enhance DPO stacking functions to allow per-instance next-nodes and hence allow children to stack onto the interface per-instance tx node and not on 'interface-output'. 2) update PPPoE code to use ta midchain stack on a interface-tx DPO of the encap-interface. This remove the need for pppoe_encap node (which is replaced by the adj-midchain-tx) and interface-output node is no longer used (see above). Since PPPoE encap node is no longer needed, the PPPoE seesion does not need to be retrieved in the data-path, hence the cahce misses are removed. Change-Id: Id8b40f53daa14889a9c51d802e14fed7fba4399a Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-08-08L2 over MPLSNeale Ranns1-44/+35
[support for VPWS/VPLS] - switch to using dpo_proto_t rather than fib_protocol_t in fib_paths so that we can describe L2 paths - VLIB nodes to handle pop/push of MPLS labels to L2 Change-Id: Id050d06a11fd2c9c1c81ce5a0654e6c5ae6afa6e Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-08-01FIB path weight incorrect in dump (VPP-922)Neale Ranns1-2/+3
Change-Id: I655f41878ca3595681d0255782b0faba01c9824b Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-07-31Fix fib_path encoding (VPP-921)Florin Coras1-0/+2
Change-Id: I4c3b22c333b052d068f1a5977e9d4e38471693d6 Signed-off-by: Florin Coras <fcoras@cisco.com>
2017-07-18FIB path preferenceNeale Ranns1-4/+43
Paths are given a preference, lowest value is 'best'. Only paths that are up are up contribute to fprwarding - that's unchanged. What's new is that of the path's that re up only those that have the best preference contribute. A poor man's primary and backup. It's not true primary/backup function because the FIB must converge before the lower preference paths are used. Change-Id: Ie4453c4a7b1094c6c2b51fe1594b8302103bb68e Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-23Labelled attached paths via an MPLS tunnelNeale Ranns1-26/+44
Change-Id: Ic86617c9c3217122043656ce2ea70bb106df5b2d Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-23ARP/ND entries for the same address on different interfaces (VPP-848)Neale Ranns1-3/+3
there are, intentionally, no validation checks in the ARP/ND code to prevent an ARP/ND entry from being installed for an address that is not local to the interface's sub-net. This is ok, since the adjacency/FIB code is designed to handle this case using the 'refinement' criteria - i.e. only installing a FIB entry for the address if the address 'refines' (i.e. is more specific than) the interface's sub-net. However, the refinement criteria currently operates on the FIB entry's prefix (which is a /32, so on the address) and not on the next-hop in the path. So, enter multiple ARP entries for the same address on different links, and this refinement criteria uses only the last added path, and so will remove the FIB entry should the ARP entries be added in the 'wrong' order. This fix updates the refinement criteria to work on each path of the FIB entry. The entry is installed if one of the paths refines the covers and only paths refining the cover contribute forwarding. Per-path refinement checks are stored in path-extensions. The patch is rather large as path-extension, which were previously used only for out-going MPLS labels, have been generalized. Change-Id: I00be359148cb948c32c52109e832a70537a7920a Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-15Fix FIB recursion loops via cover (VPP-842)Neale Ranns1-3/+8
Change-Id: Ia91c3e8cb27b9e4c1cccefc0a4857dd9995450ab Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-24Improve Load-Balance MAPsNeale Ranns1-2/+4
- only build them for popular path-lists (where popular means more than 64 children) the reason to have a map is to improve convergence speed for recursive prefixes - if there are only a few this technique is not needed - only build them when there is at least one path that has recursive constraints, i.e. a path that can 'fail' in a PIC scenario. - Use the MAPS in the switch path. - PIC test cases for functionality (not convergence performance) Change-Id: I70705444c8469d22b07ae34be82cfb6a01358e10 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-13Remove unsed parameter from fib_table_entry_special_add() (only used in FIB ↵Neale Ranns1-2/+1
tests). The DPO was incorrectly initialised with FIB_PROTO_MAX Change-Id: I962df9e162e4dfb6837a5ce79ea795d5ff2d7315 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-11MPLS Mcast coverity fixesNeale Ranns1-1/+1
Change-Id: Ic07ec5d4c2560a414d5f4f7eb37e10faf591664a Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-11Remove usued, redundant and deprecated code from lookup.hNeale Ranns1-19/+0
Change-Id: Ic16bc10d0b2877b2afdf052615f9334f31b9519f Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-07MPLS McastNeale Ranns1-44/+178
1 - interface-DPO Used in the Data-plane to change a packet's input interface 2 - MPLS multicast FIB entry Same as a unicast entry but it links to a replicate not a load-balance DPO 3 - Multicast MPLS tunnel Update MPLS tunnels to use a FIB path-list to describe the endpoint[s]. Use the path-list to generate the forwarding chain (DPOs) to link to . 4 - Resolve a path via a local label (of an mLDP LSP) For IP multicast entries to use an LSP in the replication list, we need to decribe the 'resolve-via-label' where the label is that of a multicast LSP. 5 - MPLS disposition path sets RPF-ID For a interface-less LSP (i.e. mLDP not RSVP-TE) at the tail of the LSP we still need to perform an RPF check. An MPLS disposition DPO performs the MPLS pop validation checks and sets the RPF-ID in the packet. 6 - RPF check with per-entry RPF-ID An RPF-ID is used instead of a real interface SW if index in the case the IP traffic arrives from an LSP that does not have an associated interface. Change-Id: Ib92e177be919147bafeb599729abf3d1abc2f4b3 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-06BFD-FIB interactionsNeale Ranns1-15/+37
- single-hop BFD: attach a delegate to the appropriate adjacency - multi-hop BFD [not supported yet]: attach a delegate to the FIB entry. adjacency/fib_entry state tracks the BFD session state. when the state is down the object does not contribute forwarding hence and hence dependent objects will not use it. For example, if a route is ECMP via two adjacencies and one of them is BFD down, then only the other is used to forward (i.e. we don't drop half the traffic). Change-Id: I0ef53e20e73b067001a132cd0a3045408811a822 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-01MTRIE Optimisations 2Neale Ranns1-0/+1
1) 16-8-8 stride. Reduce trie depth walk traded with increased memory in the top PLY. 2) separate the vector of protocol-independent (PI) fib_table_t with the vector of protocol dependent (PD) FIBs. PD FIBs are large structures, we don't want to burn the memory for ech PD type 3) Go straight to the PD FIB in the data-path thus avoiding an indirection through, e.g., a PLY pool. Change-Id: I800d1ed0b2049040d5da95213f3ed6b12bdd78b7 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-03-17Attached hostsNeale Ranns1-0/+7
allow this config to function: set int ip address loop0 169.254.1.1/32 (the default GW address for attached hosts) set int unnumbered af_packet0 use loop0 ('enable' IP on the host interface) ip route add 192.168.1.1/32 via af_packet0 (where to find the host) repeat for each host and host interface. Inter-host communication is throught the /32 routes. To allow this: 1 - attached host routes have the ATTACHED flag set, so the ARP code accepts then as legitimate sources 2 - unnumbered interfaces inherit the source address from the IP interface Change-Id: Ib66c5f0e848c528f79372813adc3a0c11b50717f Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-02-13Basic support for LISP-GPE encapsulated NSH packetsFlorin Coras1-0/+4
Change-Id: I97fedb0f70dd18ed9bbe985407cc5fe714e8a2e2 Signed-off-by: Florin Coras <fcoras@cisco.com>
2017-01-27IP Multicast FIB (mfib)Neale Ranns1-29/+62
- IPv[46] mfib tables with support for (*,G/m), (*,G) and (S,G) exact and longest prefix match - Replication represented via a new replicate DPO. - RPF configuration and data-plane checking - data-plane signals sent to listening control planes. The functions of multicast forwarding entries differ from their unicast conterparts, so we introduce a new mfib_table_t and mfib_entry_t objects. However, we re-use the fib_path_list to resolve and build the entry's output list. the fib_path_list provides the service to construct a replicate DPO for multicast. 'make tests' is added to with two new suites; TEST=mfib, this is invocation of the CLI command 'test mfib' which deals with many path add/remove, flag set/unset scenarios, TEST=ip-mcast, data-plane forwarding tests. Updated applications to use the new MIFB functions; - IPv6 NS/RA. - DHCPv6 unit tests for these are undated accordingly. Change-Id: I49ec37b01f1b170335a5697541c8fd30e6d3a961 Signed-off-by: Neale Ranns <nranns@cisco.com>
2016-12-28Reorganize source tree to use single autotools instanceDamjan Marion1-0/+2001
Change-Id: I7b51f88292e057c6443b12224486f2d0c9f8ae23 Signed-off-by: Damjan Marion <damarion@cisco.com>