summaryrefslogtreecommitdiffstats
path: root/src/vnet/fib/fib_path_ext.c
AgeCommit message (Collapse)AuthorFilesLines
2021-12-21fib: MPLS EOS chains built for attached prefixes should link to a lookup DPONeale Ranns1-2/+3
Type: fix Presently a local label associated with an attached or connected prefix will link to the glean. This is a problem since it will never use the adj-fibs that are installed for that attached prefix. Instead link the local label to a lookup in the table in which the attached link is bound. Signed-off-by: Neale Ranns <neale@graphiant.com> Change-Id: Iad49fb6168b9ba47216a9a52bd262363b49c3c43
2018-12-20FIB: encode the label stack in the FIB path during table dumpNeale Ranns1-3/+6
Change-Id: I28e8a99b980ad343a4209e673201791b91ceab4e Signed-off-by: Neale Ranns <nranns@cisco.com>
2018-08-27IGMP: enable command on cliNeale Ranns1-2/+1
Change-Id: I1f741b66ab8e3ecbb5c0d248b72e52c56545d5f3 Signed-off-by: Neale Ranns <nranns@cisco.com>
2018-03-09MPLS Unifom modeNeale Ranns1-21/+56
- support both pipe and uniform modes for all MPLS LSP - all API programming for output-labels requires that the mode (and associated data) is specificed - API changes in MPLS, BIER and IP are involved - new DPO [sub] types for MPLS labels to handle the two modes. Change-Id: I87b76401e996f10dfbdbe4552ff6b19af958783c Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-11-11MPLS disposition actions at the tail of unicast LSPsNeale Ranns1-0/+9
Change-Id: I8c42e26152f2ed1246f91b789887bfc923418bdf Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-08-08L2 over MPLSNeale Ranns1-0/+3
[support for VPWS/VPLS] - switch to using dpo_proto_t rather than fib_protocol_t in fib_paths so that we can describe L2 paths - VLIB nodes to handle pop/push of MPLS labels to L2 Change-Id: Id050d06a11fd2c9c1c81ce5a0654e6c5ae6afa6e Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-26ARP/ND use path_remove to complement path_addNeale Ranns1-3/+14
don't add duplicate extensions. Change-Id: Icf72d6e1b004d0dda532bec2b51f6b74544925bb Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-23ARP/ND entries for the same address on different interfaces (VPP-848)Neale Ranns1-10/+203
there are, intentionally, no validation checks in the ARP/ND code to prevent an ARP/ND entry from being installed for an address that is not local to the interface's sub-net. This is ok, since the adjacency/FIB code is designed to handle this case using the 'refinement' criteria - i.e. only installing a FIB entry for the address if the address 'refines' (i.e. is more specific than) the interface's sub-net. However, the refinement criteria currently operates on the FIB entry's prefix (which is a /32, so on the address) and not on the next-hop in the path. So, enter multiple ARP entries for the same address on different links, and this refinement criteria uses only the last added path, and so will remove the FIB entry should the ARP entries be added in the 'wrong' order. This fix updates the refinement criteria to work on each path of the FIB entry. The entry is installed if one of the paths refines the covers and only paths refining the cover contribute forwarding. Per-path refinement checks are stored in path-extensions. The patch is rather large as path-extension, which were previously used only for out-going MPLS labels, have been generalized. Change-Id: I00be359148cb948c32c52109e832a70537a7920a Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-07MPLS McastNeale Ranns1-2/+2
1 - interface-DPO Used in the Data-plane to change a packet's input interface 2 - MPLS multicast FIB entry Same as a unicast entry but it links to a replicate not a load-balance DPO 3 - Multicast MPLS tunnel Update MPLS tunnels to use a FIB path-list to describe the endpoint[s]. Use the path-list to generate the forwarding chain (DPOs) to link to . 4 - Resolve a path via a local label (of an mLDP LSP) For IP multicast entries to use an LSP in the replication list, we need to decribe the 'resolve-via-label' where the label is that of a multicast LSP. 5 - MPLS disposition path sets RPF-ID For a interface-less LSP (i.e. mLDP not RSVP-TE) at the tail of the LSP we still need to perform an RPF check. An MPLS disposition DPO performs the MPLS pop validation checks and sets the RPF-ID in the packet. 6 - RPF check with per-entry RPF-ID An RPF-ID is used instead of a real interface SW if index in the case the IP traffic arrives from an LSP that does not have an associated interface. Change-Id: Ib92e177be919147bafeb599729abf3d1abc2f4b3 Signed-off-by: Neale Ranns <nranns@cisco.com>
2016-12-28Reorganize source tree to use single autotools instanceDamjan Marion1-0/+231
Change-Id: I7b51f88292e057c6443b12224486f2d0c9f8ae23 Signed-off-by: Damjan Marion <damarion@cisco.com>