aboutsummaryrefslogtreecommitdiffstats
path: root/src/vnet/fib/fib_path_ext.h
AgeCommit message (Collapse)AuthorFilesLines
2018-03-09MPLS Unifom modeNeale Ranns1-1/+33
- support both pipe and uniform modes for all MPLS LSP - all API programming for output-labels requires that the mode (and associated data) is specificed - API changes in MPLS, BIER and IP are involved - new DPO [sub] types for MPLS labels to handle the two modes. Change-Id: I87b76401e996f10dfbdbe4552ff6b19af958783c Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-26ARP/ND use path_remove to complement path_addNeale Ranns1-5/+5
don't add duplicate extensions. Change-Id: Icf72d6e1b004d0dda532bec2b51f6b74544925bb Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-23ARP/ND entries for the same address on different interfaces (VPP-848)Neale Ranns1-7/+81
there are, intentionally, no validation checks in the ARP/ND code to prevent an ARP/ND entry from being installed for an address that is not local to the interface's sub-net. This is ok, since the adjacency/FIB code is designed to handle this case using the 'refinement' criteria - i.e. only installing a FIB entry for the address if the address 'refines' (i.e. is more specific than) the interface's sub-net. However, the refinement criteria currently operates on the FIB entry's prefix (which is a /32, so on the address) and not on the next-hop in the path. So, enter multiple ARP entries for the same address on different links, and this refinement criteria uses only the last added path, and so will remove the FIB entry should the ARP entries be added in the 'wrong' order. This fix updates the refinement criteria to work on each path of the FIB entry. The entry is installed if one of the paths refines the covers and only paths refining the cover contribute forwarding. Per-path refinement checks are stored in path-extensions. The patch is rather large as path-extension, which were previously used only for out-going MPLS labels, have been generalized. Change-Id: I00be359148cb948c32c52109e832a70537a7920a Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-07MPLS McastNeale Ranns1-1/+2
1 - interface-DPO Used in the Data-plane to change a packet's input interface 2 - MPLS multicast FIB entry Same as a unicast entry but it links to a replicate not a load-balance DPO 3 - Multicast MPLS tunnel Update MPLS tunnels to use a FIB path-list to describe the endpoint[s]. Use the path-list to generate the forwarding chain (DPOs) to link to . 4 - Resolve a path via a local label (of an mLDP LSP) For IP multicast entries to use an LSP in the replication list, we need to decribe the 'resolve-via-label' where the label is that of a multicast LSP. 5 - MPLS disposition path sets RPF-ID For a interface-less LSP (i.e. mLDP not RSVP-TE) at the tail of the LSP we still need to perform an RPF check. An MPLS disposition DPO performs the MPLS pop validation checks and sets the RPF-ID in the packet. 6 - RPF check with per-entry RPF-ID An RPF-ID is used instead of a real interface SW if index in the case the IP traffic arrives from an LSP that does not have an associated interface. Change-Id: Ib92e177be919147bafeb599729abf3d1abc2f4b3 Signed-off-by: Neale Ranns <nranns@cisco.com>
2016-12-28Reorganize source tree to use single autotools instanceDamjan Marion1-0/+69
Change-Id: I7b51f88292e057c6443b12224486f2d0c9f8ae23 Signed-off-by: Damjan Marion <damarion@cisco.com>