summaryrefslogtreecommitdiffstats
path: root/src/vnet/fib/fib_table.c
AgeCommit message (Collapse)AuthorFilesLines
2017-09-13Add a name to the creation of an IP and MPLS tableNeale Ranns1-7/+37
Change-Id: I4b4648831551519b2ffb6f93255d28a4b8726c22 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-09-11FIB table add/delete APINeale Ranns1-12/+31
part 2; - this adds the code to create an IP and MPLS table via the API. - but the enforcement that the table must be created before it is used is still missing, this is so that CSIT can pass. Change-Id: Id124d884ade6cb7da947225200e3bb193454c555 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-08-08L2 over MPLSNeale Ranns1-3/+3
[support for VPWS/VPLS] - switch to using dpo_proto_t rather than fib_protocol_t in fib_paths so that we can describe L2 paths - VLIB nodes to handle pop/push of MPLS labels to L2 Change-Id: Id050d06a11fd2c9c1c81ce5a0654e6c5ae6afa6e Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-05-02Use per-protocol default flow-hash config when the FIB table index is not knownNeale Ranns1-0/+16
Change-Id: If088e75801831befc6bddb77ea20abe9288b93c4 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-26IP Flow Hash Config fixesNeale Ranns1-10/+44
- the flow hash config is (and was) cached on the load-balance object so the fib_table_t struct is not used a switch time. Therefore changes to the table's flow hash config need to be propagated to all load-balances and hance all FIB entries in the table. - enable API for setting the IPv6 table flow hash config - use only the hash config in the fib_table_t object and not on the ipX_fib_t - add tests. Change-Id: Ib804c11162c6d4972c764957562c372f663e05d4 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-24Improve Load-Balance MAPsNeale Ranns1-2/+10
- only build them for popular path-lists (where popular means more than 64 children) the reason to have a map is to improve convergence speed for recursive prefixes - if there are only a few this technique is not needed - only build them when there is at least one path that has recursive constraints, i.e. a path that can 'fail' in a PIC scenario. - Use the MAPS in the switch path. - PIC test cases for functionality (not convergence performance) Change-Id: I70705444c8469d22b07ae34be82cfb6a01358e10 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-13Remove unsed parameter from fib_table_entry_special_add() (only used in FIB ↵Neale Ranns1-13/+2
tests). The DPO was incorrectly initialised with FIB_PROTO_MAX Change-Id: I962df9e162e4dfb6837a5ce79ea795d5ff2d7315 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-07MPLS McastNeale Ranns1-10/+37
1 - interface-DPO Used in the Data-plane to change a packet's input interface 2 - MPLS multicast FIB entry Same as a unicast entry but it links to a replicate not a load-balance DPO 3 - Multicast MPLS tunnel Update MPLS tunnels to use a FIB path-list to describe the endpoint[s]. Use the path-list to generate the forwarding chain (DPOs) to link to . 4 - Resolve a path via a local label (of an mLDP LSP) For IP multicast entries to use an LSP in the replication list, we need to decribe the 'resolve-via-label' where the label is that of a multicast LSP. 5 - MPLS disposition path sets RPF-ID For a interface-less LSP (i.e. mLDP not RSVP-TE) at the tail of the LSP we still need to perform an RPF check. An MPLS disposition DPO performs the MPLS pop validation checks and sets the RPF-ID in the packet. 6 - RPF check with per-entry RPF-ID An RPF-ID is used instead of a real interface SW if index in the case the IP traffic arrives from an LSP that does not have an associated interface. Change-Id: Ib92e177be919147bafeb599729abf3d1abc2f4b3 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-01MTRIE Optimisations 2Neale Ranns1-11/+13
1) 16-8-8 stride. Reduce trie depth walk traded with increased memory in the top PLY. 2) separate the vector of protocol-independent (PI) fib_table_t with the vector of protocol dependent (PD) FIBs. PD FIBs are large structures, we don't want to burn the memory for ech PD type 3) Go straight to the PD FIB in the data-path thus avoiding an indirection through, e.g., a PLY pool. Change-Id: I800d1ed0b2049040d5da95213f3ed6b12bdd78b7 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-03-17Attached hostsNeale Ranns1-0/+1
allow this config to function: set int ip address loop0 169.254.1.1/32 (the default GW address for attached hosts) set int unnumbered af_packet0 use loop0 ('enable' IP on the host interface) ip route add 192.168.1.1/32 via af_packet0 (where to find the host) repeat for each host and host interface. Inter-host communication is throught the /32 routes. To allow this: 1 - attached host routes have the ATTACHED flag set, so the ARP code accepts then as legitimate sources 2 - unnumbered interfaces inherit the source address from the IP interface Change-Id: Ib66c5f0e848c528f79372813adc3a0c11b50717f Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-02-20FIB reset leaves residual routes. Wrong API used to remove the routes meant ↵Neale Ranns1-1/+1
the lock count on the entry did not drop to zero Change-Id: I6e2dff8c3c7976fd1c2e4c5258f5dc73123aa9b7 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-02-20Python test IP and MPLS objects conform to infra.Neale Ranns1-1/+1
Add IP[46] MFIB dump. Change-Id: I4a2821f65e67a5416b291e4912c84f64989883b8 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-01-27IP Multicast FIB (mfib)Neale Ranns1-2/+67
- IPv[46] mfib tables with support for (*,G/m), (*,G) and (S,G) exact and longest prefix match - Replication represented via a new replicate DPO. - RPF configuration and data-plane checking - data-plane signals sent to listening control planes. The functions of multicast forwarding entries differ from their unicast conterparts, so we introduce a new mfib_table_t and mfib_entry_t objects. However, we re-use the fib_path_list to resolve and build the entry's output list. the fib_path_list provides the service to construct a replicate DPO for multicast. 'make tests' is added to with two new suites; TEST=mfib, this is invocation of the CLI command 'test mfib' which deals with many path add/remove, flag set/unset scenarios, TEST=ip-mcast, data-plane forwarding tests. Updated applications to use the new MIFB functions; - IPv6 NS/RA. - DHCPv6 unit tests for these are undated accordingly. Change-Id: I49ec37b01f1b170335a5697541c8fd30e6d3a961 Signed-off-by: Neale Ranns <nranns@cisco.com>
2016-12-28Reorganize source tree to use single autotools instanceDamjan Marion1-0/+1104
Change-Id: I7b51f88292e057c6443b12224486f2d0c9f8ae23 Signed-off-by: Damjan Marion <damarion@cisco.com>