Age | Commit message (Collapse) | Author | Files | Lines |
|
Type: fix
it was marked MP safe in the CLI (which it shouldn't be) but
it it not marked MP safe on the API.
Change-Id: I4bdea498a510a8b406d13d62a899b6d03656f7e8
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Type: feature
- ip-neighbour: generic neighbour handling; APIs, DBs, event handling,
aging
- arp: ARP protocol implementation
- ip6-nd; IPv6 neighbor discovery implementation; separate ND,
MLD, RA
- ip6-link; manage link-local addresses
- l2-arp-term; events separated from IP neighbours, since they are not
the same.
vnet retains just enough education to perform ND/ARP packet
construction.
arp and ip6-nd to be moved to plugins soon.
Change-Id: I88dedd0006b299344f4c7024a0aa5baa6b9a8bbe
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Type: fix
if the packet is about to be fragmented, then don't call any of the
actions that expect the rewrite to have been written.
1) don't double count packets thru the adjacency (original & fragments)
2) don't double decrement the TTL for fragments
3) return to ip4-midchain post ip-frag if that's where we started.
4) only run midchain/mcast fixups if not fragmenting (if no errors)
Change-Id: Ib2866787a42713ee5871b87b597d8f74b901044b
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Type: style
Change-Id: I7d44b7fab1b8b196e4934cb4832ee51084c5bf98
Signed-off-by: Paul Vinciguerra <pvinci@vinciconsulting.com>
|
|
Type: fix
Change-Id: I7ed9726d8c5ca26715a84b004a18fd7f93142486
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Type: fix
Change-Id: I6fd7bb27b95a50d37424f65dc51e8b341f8b1b28
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
In some cases, we can refer to no-longer adjacencies (eg. in traces). Do
not dump them in this case as they are probably incorrect (memory can be
reused).
Type: fix
Change-Id: Ib653ba066bb6595ec6ec37d313a3124bce0eeed3
Signed-off-by: Benoît Ganne <bganne@cisco.com>
|
|
Type: feature
Adding a prefix to an interface was not permitted if it overlapped
with another prefix on an interface which used the same FIB.
Loosen the restriction. Allow 2 or more addresses from the same
prefix on a single interface. Reference count the prefix to figure
out when a glean/connected route for the prefix needs to be added
or removed.
Added unit tests to check that the route is only removed when all
addresses in the prefix are removed from the interface.
Change-Id: I1a962ecb5e1ee65fc6d41f98a4cc097a51a55321
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
Enhance the route add/del APIs to take a set of paths rather than just one.
Most unicast routing protocols calcualte all the available paths in one
run of the algorithm so updating all the paths at once is beneficial for the client.
two knobs control the behaviour:
is_multipath - if set the the set of paths passed will be added to those
that already exist, otherwise the set will replace them.
is_add - add or remove the set
is_add=0, is_multipath=1 and an empty set, results in deleting the route.
It is also considerably faster to add multiple paths at once, than one at a time:
vat# ip_add_del_route 1.1.1.1/32 count 100000 multipath via 10.10.10.11
100000 routes in .572240 secs, 174751.80 routes/sec
vat# ip_add_del_route 1.1.1.1/32 count 100000 multipath via 10.10.10.12
100000 routes in .528383 secs, 189256.54 routes/sec
vat# ip_add_del_route 1.1.1.1/32 count 100000 multipath via 10.10.10.13
100000 routes in .757131 secs, 132077.52 routes/sec
vat# ip_add_del_route 1.1.1.1/32 count 100000 multipath via 10.10.10.14
100000 routes in .878317 secs, 113854.12 routes/sec
vat# ip_route_add_del 1.1.1.1/32 count 100000 multipath via 10.10.10.11 via 10.10.10.12 via 10.10.10.13 via 10.10.10.14
100000 routes in .900212 secs, 111084.93 routes/sec
Change-Id: I416b93f7684745099c1adb0b33edac58c9339c1a
Signed-off-by: Neale Ranns <neale.ranns@cisco.com>
Signed-off-by: Ole Troan <ot@cisco.com>
Signed-off-by: Paul Vinciguerra <pvinci@vinciconsulting.com>
|
|
use address_t and mac_address_t for IPv6 and ARP entries
and all other API calls in ip.api aprat from the route ones,
that will follow in a separate commit
Change-Id: I67161737c2184d3f8fc1e79ebd2b55121c5b0191
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I7cf3ae8c10dd584e8bc234a3253bea3c5a2d105a
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: Ied34720ca5a6e6e717eea4e86003e854031b6eab
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
Change-Id: I3cb89dbfb7174b9913a8c4ad9b3b1dc9f6ed6326
Signed-off-by: Matus Fabian <matfabia@cisco.com>
|
|
Change-Id: I221cebddc45efbfdec428b7df2af96e2aedff2dd
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I8dc6230b65e57ddc07f974bf6726393d8dbfd4a2
Signed-off-by: Yichen Wang <yicwang@cisco.com>
|
|
Change-Id: I12fbebd1d24c37dc77c147773ea522c8a4b7b99d
Signed-off-by: John Lo <loj@cisco.com>
|
|
Change-Id: I5e29e16b4d45411b1a7c177b8d7156c5baefe6a1
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I5e679f2601e37688f2768620479dc2efb7d19ca3
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
This change makes ip reassembly an interface feature, while adding
concurrency support. Due to this, punt is no longer needed to test
reassembly.
Change-Id: I467669514ec33283ce935be0f1dd08f07684f0c7
Signed-off-by: Klement Sekera <ksekera@cisco.com>
|
|
Change-Id: Ie5a50def4ec1e4a3b3404a8b6ab9ec248bc16744
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
and update glean address on local interface MAC change
Change-Id: I530826d60c7e9db2b0fa2d45754139d82c5ea807
Signed-off-by: Neale Ranns <neale.ranns@cisco.com>
|
|
This reverts commit 8b30e471df4d42214619e1d6c50cc8298426b45f.
Change-Id: I99edb236eb0a7f8ba3fba333c3481a710ebcb59c
Signed-off-by: Ole Troan <ot@cisco.com>
|
|
update the glean adj on a local interface MAC change
Change-Id: Ia5c5cde424ed0fea3431532cc5abf22b364bbab5
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: Ic5dcadd13c88b8a5e7896dab82404509c081614a
Signed-off-by: Klement Sekera <ksekera@cisco.com>
|
|
Change-Id: I565277eafbce3d4f59a7f0d497fca1c4fed3cfc8
Signed-off-by: Swarup Nayak <swarupnpvt@gmail.com>
|
|
Change-Id: I32de25890ac0a643314f650591d2479879d9a2a6
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I5e35921acb65157a3de8ea0c53b3a6fa5cfca044
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
A UDP-encap object that particiapates in the FIB graph and contributes
DPO to teh output chain. It thereofre resembles a tunnel but without the
interface. FIB paths (and henace routes) can then be created to egress
through the UDP-encap. Said routes can have MPLS labels, hence this also
allows MPLSoUPD.
Encap is uni-directional. For decap, one still registers with the UDP port
dispatcher.
Change-Id: I23bd345523b20789a1de1b02022ea1148ca50797
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: Id324a757517f85973097e20e2eb88d64ae0e931b
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
Change-Id: I4164c4c19c8dbfd73e6ddf94a12056325cc093b9
Signed-off-by: Neale Ranns <nranns@cisco.com>
Signed-off-by: Andrew Yourtchenko <ayourtch@gmail.com>
|
|
Identify and complain when the same IP prefix is assigned
to two different SW interfaces:
vpp# set int ip address TenGigabitEthernet6/0/0 1.2.3.4/32
vpp# set int ip address TenGigabitEthernet6/0/1 1.2.3.4/32
set interface ip address: Prefix 1.2.3.4/32 already found on
interface TenGigabitEthernet6/0/0
Change-Id: I1aee1b6a7ddd00d3109a53d8e1b6ce97bf45e372
Signed-off-by: Jon Loeliger <jdl@netgate.com>
|
|
Change-Id: I4b4648831551519b2ffb6f93255d28a4b8726c22
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
part 2;
- this adds the code to create an IP and MPLS table via the API.
- but the enforcement that the table must be created before it is used is still missing, this is so that CSIT can pass.
Change-Id: Id124d884ade6cb7da947225200e3bb193454c555
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: Ie1fba1a32020775444c7b1ed800e8559b54691ff
Signed-off-by: pragash <pxv3620@rit.edu>
|
|
Change-Id: Ib5af105e32b6b0df86923e189ab6bf6ee59de5b9
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
[support for VPWS/VPLS]
- switch to using dpo_proto_t rather than fib_protocol_t in fib_paths so that we can describe L2 paths
- VLIB nodes to handle pop/push of MPLS labels to L2
Change-Id: Id050d06a11fd2c9c1c81ce5a0654e6c5ae6afa6e
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Paths are given a preference, lowest value is 'best'. Only paths that are up are up contribute to fprwarding - that's unchanged. What's new is that of the path's that re up only those that have the best preference contribute. A poor man's primary and backup. It's not true primary/backup function because the FIB must converge before the lower preference paths are used.
Change-Id: Ie4453c4a7b1094c6c2b51fe1594b8302103bb68e
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I1b71010e20742eee02693d672e24c85897e37759
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I046d9402b79fdbc6a6663199ffff8e40a278fd51
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: Ic16bc10d0b2877b2afdf052615f9334f31b9519f
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
1 - interface-DPO
Used in the Data-plane to change a packet's input interface
2 - MPLS multicast FIB entry
Same as a unicast entry but it links to a replicate not a load-balance DPO
3 - Multicast MPLS tunnel
Update MPLS tunnels to use a FIB path-list to describe the endpoint[s]. Use the path-list to generate the forwarding chain (DPOs) to link to .
4 - Resolve a path via a local label (of an mLDP LSP)
For IP multicast entries to use an LSP in the replication list, we need to decribe the 'resolve-via-label' where the label is that of a multicast LSP.
5 - MPLS disposition path sets RPF-ID
For a interface-less LSP (i.e. mLDP not RSVP-TE) at the tail of the LSP we still need to perform an RPF check. An MPLS disposition DPO performs the MPLS pop validation checks and sets the RPF-ID in the packet.
6 - RPF check with per-entry RPF-ID
An RPF-ID is used instead of a real interface SW if index in the case the IP traffic arrives from an LSP that does not have an associated interface.
Change-Id: Ib92e177be919147bafeb599729abf3d1abc2f4b3
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I2d1c5e4dbdcab2a81d6c88801183ca0bbc83e1d9
Signed-off-by: flyingeagle23 <wang.hui56@zte.com.cn>
|
|
Change-Id: I03195a86c69f84a301051c6b3ab64456bbf28645
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
node_index memeber from the rewrite for space - this is only used for formtting
before:
ip4-rewrite * * * * 2.66e1 256.00
after:
ip4-rewrite * * * * 2.40e1 256.00
Change-Id: Ic397150727cad38811564777419ad6bd26b8a3a6
Signed-off-by: Neale Ranns <nranns@wasa-ucs-11.cisco.com>
|
|
Change-Id: Ia9c6790436f8f6337b5351e3017ef5e441a8a4e9
Signed-off-by: Neale Ranns <nranns@cisco.com>
(cherry picked from commit 5e323329ed6ded6f6944c56069329207ad9069c0)
|
|
bridging. That is hosts in one sub-net reachable via differenet interfaces.
Introducate a new API command:
ip6 nd proxy <host-address> <interface>
this indicates 2 things;
1) that host <host-address> is reachable out of interface <interface>. VPP will thus install that route.
2) NS requests sent to <host-address> will be responeded to (i.e. proxied).
Change-Id: I863f967fdb5097ab3b574769c70afdbfc8d5478a
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
In the CLI parsing, below is a common pattern:
/* Get a line of input. */
if (!unformat_user (input, unformat_line_input, line_input))
return 0;
while (unformat_check_input (line_input) != UNFORMAT_END_OF_INPUT)
{
if (unformat (line_input, "x"))
x = 1;
:
else
return clib_error_return (0, "unknown input `%U'",
format_unformat_error, line_input);
}
unformat_free (line_input);
The 'else' returns if an unknown string is encountered. There a memory
leak because the 'unformat_free(line_input)' is not called. There is a
large number of instances of this pattern.
Replaced the previous pattern with:
/* Get a line of input. */
if (!unformat_user (input, unformat_line_input, line_input))
return 0;
while (unformat_check_input (line_input) != UNFORMAT_END_OF_INPUT)
{
if (unformat (line_input, "x"))
x = 1;
:
else
{
error = clib_error_return (0, "unknown input `%U'",
format_unformat_error, line_input);
goto done:
}
}
/* ...Remaining code... */
done:
unformat_free (line_input);
return error;
}
In multiple files, 'unformat_free (line_input);' was never called, so
there was a memory leak whether an invalid string was entered or not.
Also, there were multiple instance where:
error = clib_error_return (0, "unknown input `%U'",
format_unformat_error, line_input);
used 'input' as the last parameter instead of 'line_input'. The result
is that output did not contain the substring in error, instead just an
empty string. Fixed all of those as well.
There are a lot of file, and very mind numbing work, so tried to keep
it to a pattern to avoid mistakes.
Change-Id: I8902f0c32a47dd7fb3bb3471a89818571702f1d2
Signed-off-by: Billy McFall <bmcfall@redhat.com>
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
Change-Id: Id17060fd0e8ac80c8cf1999b0b82d0241b3b969a
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
- IPv[46] mfib tables with support for (*,G/m), (*,G) and (S,G) exact and longest prefix match
- Replication represented via a new replicate DPO.
- RPF configuration and data-plane checking
- data-plane signals sent to listening control planes.
The functions of multicast forwarding entries differ from their unicast conterparts, so we introduce a new mfib_table_t and mfib_entry_t objects. However, we re-use the fib_path_list to resolve and build the entry's output list. the fib_path_list provides the service to construct a replicate DPO for multicast.
'make tests' is added to with two new suites; TEST=mfib, this is invocation of the CLI command 'test mfib' which deals with many path add/remove, flag set/unset scenarios, TEST=ip-mcast, data-plane forwarding tests.
Updated applications to use the new MIFB functions;
- IPv6 NS/RA.
- DHCPv6
unit tests for these are undated accordingly.
Change-Id: I49ec37b01f1b170335a5697541c8fd30e6d3a961
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I7b51f88292e057c6443b12224486f2d0c9f8ae23
Signed-off-by: Damjan Marion <damarion@cisco.com>
|