Age | Commit message (Collapse) | Author | Files | Lines |
|
Change-Id: Iaa28f96d613d6fb75bd29958d757de206448eb22
Signed-off-by: Dave Barach <dave@barachs.net>
|
|
Due to union, l2 sub-interface bits were wrongly set
causing sporadic misconfiguration of l2 mode on some
interfaces.
Change-Id: Id77ee281e3a0030878641a786c22ffe16ce1c759
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
It is much cheaper to use ctzll than to do shift,subtract and mask
in likely case when we are looking for 1st set bit in the uword.
Change-Id: I31954081571978878c7098bafad0c85a91755fa2
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: Ibea4a96bdec5e368301a03d8b11a0712fa0265e0
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Change-Id: Ic5304749935f69018eb00183bb4670bb9f16273c
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
The pointer to IP header was derived from l3_hdr_offset,
which would be ok, if l3_hdr_offset was valid. But it does not
have to be, so it was a bad solution. Now the previous nodes
mark whether it is a IPv6 or IPv4 packet tyle, and in esp_decrypt
we count get ip header pointer by substracting the size
of the ip header from the pointer to esp header (which lies
in front of the ip header).
Change-Id: I6d425b90931053711e8ce9126811b77ae6002a16
Signed-off-by: Szymon Sliwa <szs@semihalf.com>
|
|
When a DHCP client is in the bound state, it wakes up
halfway through it's lease (by default) to try and renew
the lease. The ip4-dhcp-client-detect is not enabled as
a feature at this point, so replies sent from the DHCP
server do not get applied to the lease. Eventually the
lease expires, the address is removed from the interface,
a new discovery is performed and the same address is added
back to the interface.
Before sending a request to renew in the bound state, enable
the feature to process the reply.
Change-Id: I95332ee0596f47df6f3c8bf8e3f0698dde9a1fc5
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
Change-Id: I1c8a14d4d51aa730f0edcf491e3c4725e2d8bd66
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
Change-Id: I65c12617ad49e4d5ef242e53988782f0cefa5684
Signed-off-by: Klement Sekera <ksekera@cisco.com>
|
|
- rework the function to declutter and avoid building more than one tx
frame
- add dual loop although benefits in my tests seem to be minimal
- improve tcp/udp echo external apps. They have slightly better
throughput than internal echo apps.
- udp bugfixes
Change-Id: Iea4a245b1b1bb407a7f403dedcce2664a49f774b
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
Change-Id: I2b50e3fc06b4e905395d4706083f12ebc76826ce
Signed-off-by: Jon Loeliger <jdl@netgate.com>
|
|
Change-Id: I9937912cd760698e39044e8ae022a90b58c8db30
Signed-off-by: Eyal Bari <ebari@cisco.com>
|
|
Change-Id: Ic1e189c22e3d344d165e0eab05ccb667eef088a9
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
|
|
Change-Id: I9363cf54b73f7cfd8622af6f1cb250438ea0d3b6
Signed-off-by: Ole Troan <ot@cisco.com>
|
|
Object sizes must evenly divide alignment requests, or vice
versa. Otherwise, only the first object will be aligned as
requested.
Three choices: add CLIB_CACHE_LINE_ALIGN_MARK(align_me) at
the end of structures, manually pad to an even divisor or multiple of
the alignment request, or use plain vectors/pools.
static assert for enforcement.
Change-Id: I41aa6ff1a58267301d32aaf4b9cd24678ac1c147
Signed-off-by: Dave Barach <dbarach@cisco.com>
|
|
Change-Id: I565d79af410825c72f291ab40178883b1bc6f1df
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
If sessions are not preallocated, the rx retries counters are not
correctly validated/initialized
Change-Id: Iaf7456f3a0e2181fcea0c370613d694f8e98276d
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
Two vxlan union/struct initializations caused gcc on
CentOS 7 to puke. Modified them to make the build
work again.
Change-Id: Iad667444b86cfde5ee4329993b520028d3b593ad
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
moving the rewrite into the tunnel struct
Change-Id: Iec74b48e13456d32957e826cffb5ea35a8ebd1a0
Signed-off-by: Eyal Bari <ebari@cisco.com>
|
|
Change-Id: I906e58b4f9827a79a6ab673f8fa2e03036c69820
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
Change-Id: I2d39e56ff605e3a24927d6330d65d0406f588381
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I5cab31639e7819c9ab7e9c9159d931b25161d00b
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
- move the IPv6 incomplete and glean node to ip6_neighbour.c (so it has access to ip6_neighbour_main_t)
- use the RA info config on the interface to find the multicast adj to use
Change-Id: I835e419072abe54fb09dafb0e7eb0a9e50eba1af
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
1 - use bit-map to re-use ID values and thus VLIB nodes
2 - free vrings
3 - free hw_address on HW interface delete (a HW * struct is memset on pool_get)
4 - free temporary node names during TX node setup
Change-Id: Id114c8bb9c844fd4ceb02fbbeb4b511ecfeb61ce
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I2794384557c6272fe217269b14a9db09eda19220
Signed-off-by: Damjan Marion <damarion@cisco.com>
|
|
Currently for VXLAN IPv4.
Change-Id: Id4b8bc0d9f6ab043810e4d1b9f28e01c27ce0660
Signed-off-by: Igor Mikhailov (imichail) <imichail@cisco.com>
|
|
It is possible for span-input to get call with sw_if_index which is greater than
sm->interfaces and crashes in span_mirror () in the following line
span_interface_t *si0 = vec_elt_at_index (sm->interfaces, sw_if_index0);
For example, span-input mirrors a main interface as source, it may actually get
call for traffic coming in from the subinterface and crashes.
The fix is simply to check if sw_if_index >= vec_len (sm->interfaces) and
punt if it is.
Change-Id: I8312eb321d638518e14ba2326fffd1a7919646ca
Signed-off-by: Steven <sluong@cisco.com>
(cherry picked from commit 516d63ff2c6671f3b0dc641511a50017a9804179)
|
|
Change-Id: I379150a88f2d53d6281be41e8bad6fc4f4e88a71
Signed-off-by: Neale Ranns <neale.ranns@cisco.com>
|
|
from encap path
Change-Id: I62a8d13495355ad5e687f13b86c2a5d360bb2b7f
Signed-off-by: Eyal Bari <ebari@cisco.com>
|
|
Change-Id: I69fee1dcf07a4d2eed69a59f0a36e63e3741ed4e
Signed-off-by: Juraj Sloboda <jsloboda@cisco.com>
|
|
When walking all adjacencies for a given {next-hop,interface} instead of
walking all the adjacencies on that interface and matching the next-hop
(which is O(n) in the number of adjacencies on that link, find all instances
of an adjacency with any link-type and wtih that {next-hop,interfacE} pair:
this is O(1).
Change-Id: Ic80399fc9e93c8df111379c039e592d8cafbab18
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
[VPP-1251]
Problem:
When the bond subinterface is removed, it was observed that we lost the lacp
partner. Show hardware shows rx counter goes up, but show interface does not
for the slave interfaces.
Cause:
We reset the interface promiscuous mode when the bond subinterface is deleted.
This causes dpdk not to accept any packet. Leave the interface in promiscuous
mode fixes the problem.
Other fixes:
There are few places we use hw_if_index as if they are sw_if_index. But they
don't necessarily have the same value. As soon as a subinterface is created,
they start to diverge. The fix is to use the correct API for the hw_if_index
and sw_if_index.
Change-Id: I1e6b8bca0a4aae396d217a141271cbf968500c91
Signed-off-by: Steven <sluong@cisco.com>
(cherry picked from commit 42c6599bf3057a7e8f4f00f5b6a9dd72af48d283)
|
|
obvious leak of parent_indices
Change-Id: I572b33de1756c8062a87c754117d990622fe12fe
Signed-off-by: Kingwel Xie <kingwel.xie@ericsson.com>
|
|
Some scenarios not involving ip[4,6]-input paths might benefit from IP
header QOS fields recorded and applied.
An example: L2 (overlay) traffic being encapsulated by VPP in VXLAN
and transmitted on another (underlay) interface might want the QOS
information carried over in the outer IP header.
Change-Id: I4d9462c47ae6ba97680edb1e53340b17cfd7845b
Signed-off-by: Igor Mikhailov (imichail) <imichail@cisco.com>
|
|
set the IS_RX flag based on CLI 'l2-input-on'
Change-Id: I53d9129a7c09f605c1eb55753426f392b1b480bc
Signed-off-by: Neale Ranns <neale.ranns@cisco.com>
|
|
Should be more resilient to ack losses
Change-Id: Icec3b93c1d290dec437fcc4e6fe5171906c9ba8a
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
Change-Id: I9ab11ba9f958c679112eb22c8db39cb269a29dc7
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
When creating an IPsec tunnel interface, allow a numeric
identifier to be set for use in the interface's name in
place of the dev instance. Default to using the dev instance
if no value is explicitly set.
When an IPsec tunnel is deleted, the interface is deleted
now instead of being kept in a pool of available hw
interfaces. Otherwise there was the possibility of
conflicting tx node names between deleted tunnels and
newly created ones.
Change-Id: Ic525466622a0dec38a845fa5871c084f6d9da380
Signed-off-by: Matthew Smith <mgsmith@netgate.com>
|
|
Change-Id: Ibf3ef82950f50b746394a731cd2e7cba1cd16ec4
Signed-off-by: John Lo <loj@cisco.com>
|
|
Change-Id: I008a4d7ad7160d1f07e7ceef712a5318a9368308
Signed-off-by: Andrey "Zed" Zaikin <zed.0xff@gmail.com>
|
|
hard code the address mask offsets. This are protocol specific and only used on ethernet when used at all.
Change-Id: Ib1f6f33682f53254ffbb5a241a1583e65420e0c7
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: I53bb1e289ba16ee6d9aed7285b18437c996077a4
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
This patch addresses the warning 182994
Change-Id: I071f3cbdf9965c7b57d444f79430ee75c66c856e
Signed-off-by: Marco Varlese <marco.varlese@suse.com>
|
|
- adds session layer support for datagram based protocols
- updates udp to work in pure connectionless and datagram mode. The
existing connected mode is now 'accessible' for apps as a dummy UDPC,
as in, connected udp, protocol.
- updates udp_echo, echo client, echo server code to work in datagram
mode.
Change-Id: I2960c0d2d246cb166005f545794ec31fe0d546dd
Signed-off-by: Florin Coras <fcoras@cisco.com>
|
|
IP header is set as data + sizeof(ethernet_header_t),
what does not need to be true. The solution is to use
l3_hdr_offset.
Change-Id: I5d9f41599ba8d8eb14ce2d9d523f82ea6e0fd10d
Signed-off-by: Szymon Sliwa <szs@semihalf.com>
|
|
Change-Id: Ieac9cf50156dbbb4962411e900d59256441915ef
Signed-off-by: Damjan Marion <damarion@cisco.com>
Signed-off-by: Klement Sekera <ksekera@cisco.com>
|
|
Change-Id: I5e679f2601e37688f2768620479dc2efb7d19ca3
Signed-off-by: Neale Ranns <nranns@cisco.com>
|
|
Change-Id: Ie20aaf0eb1a5a338a54f0de4d6da661431be5163
Signed-off-by: Klement Sekera <ksekera@cisco.com>
|
|
show vhost-user <interface> may cause a crash if interface is semi-bogus.
Semi-bogus means it is a known vpp interface which has a hw_if_index, but
it is bogus because it is not a vhost-user interface.
The fix is to add a check to reject non vhost-user interface for the
command.
Change-Id: I63f1e8bfbf46f5ec4c30f9fb3546982b63cd7cc5
Signed-off-by: Steven <sluong@cisco.com>
|
|
This patch addresses 182346, 182347, 182353.
Change-Id: I59c3d74bd3a2122b836c93e22ddb632fa032f7fe
Signed-off-by: Marco Varlese <marco.varlese@suse.com>
|