summaryrefslogtreecommitdiffstats
path: root/test/test_gre.py
AgeCommit message (Collapse)AuthorFilesLines
2019-03-04test framework: Fix wrapper functions to match API message names.Ole Troan1-6/+6
In preparation to remove the wrappers in vpp_papi_provider.py, ensure names used in tests match the actual API message names. Change-Id: I230ca4eb75aa727ff68d702e085a2edbbc6b6d19 Signed-off-by: Ole Troan <ot@cisco.com>
2019-03-01Tests: Remove all wildcard imports.Paul Vinciguerra1-8/+6
They mask dependencies and confuse third party tools. Change-Id: I24ee16bfa0d746a8e8cb99891ba8b20523048b69 Signed-off-by: Paul Vinciguerra <pvinci@vinciconsulting.com>
2018-12-07FIB recusrion loop checks traverse midchain adjacenciesNeale Ranns1-0/+61
if a tunnel's destination address is reachable through the tunnel (see example config belwo) then search for and detect a recursion loop and don't stack the adjacency. Otherwise this results in a nasty surprise. DBGvpp# loop cre DBGvpp# set int state loop0 up DBGvpp# set int ip addr loop0 10.0.0.1/24 DBGvpp# create gre tunnel src 10.0.0.1 dst 1.1.1.1 DBGvpp# set int state gre0 up DBGvpp# set int unnum gre0 use loop0 DBGvpp# ip route 1.1.1.1/32 via gre0 DBGvpp# sh ip fib 1.1.1.1 ipv4-VRF:0, fib_index:0, flow hash:[src dst sport dport proto ] locks:[src:plugin-hi:2, src:default-route:1, ] 1.1.1.1/32 fib:0 index:11 locks:4 <<< this is entry #11 src:CLI refs:1 entry-flags:attached, src-flags:added,contributing,active, path-list:[14] locks:2 flags:shared,looped, uPRF-list:12 len:1 itfs:[2, ] path:[14] pl-index:14 ip4 weight=1 pref=0 attached-nexthop: oper-flags:recursive-loop,resolved, cfg-flags:attached, 1.1.1.1 gre0 (p2p) [@0]: ipv4 via 0.0.0.0 gre0: mtu:9000 4500000000000000fe2fb0cc0a0000010101010100000800 stacked-on entry:11: <<<< and the midchain forwards via entry #11 [@2]: dpo-drop ip4 src:recursive-resolution refs:1 src-flags:added, cover:-1 forwarding: unicast-ip4-chain [@0]: dpo-load-balance: [proto:ip4 index:13 buckets:1 uRPF:12 to:[0:0]] [0] [@6]: ipv4 via 0.0.0.0 gre0: mtu:9000 4500000000000000fe2fb0cc0a0000010101010100000800 stacked-on entry:11: [@2]: dpo-drop ip4 DBGvpp# sh adj 1 [@1] ipv4 via 0.0.0.0 gre0: mtu:9000 4500000000000000fe2fb0cc0a0000010101010100000800 stacked-on entry:11: [@2]: dpo-drop ip4 flags:midchain-ip-stack midchain-looped <<<<< this is a loop counts:[0:0] locks:4 delegates: children: {path:14} Change-Id: I39b82bd1ea439be4611c88b130d40289fa0c1b59 Signed-off-by: Neale Ranns <nranns@cisco.com>
2018-11-29GRE: UT uses new pkt send functionsNeale Ranns1-108/+23
Change-Id: Icb1767b31421aa1e427498adc82d79307835ee1a Signed-off-by: Neale Ranns <nranns@cisco.com>
2018-11-29GRE: fix VRF unit-testsNeale Ranns1-3/+8
Change-Id: Ic6d011065bf062a84fdccdb1726ed3e5ed99cfbc Signed-off-by: Neale Ranns <nranns@cisco.com>
2018-09-19GRE: fix 4o6 and 6o4 adj stackingNeale Ranns1-0/+87
Change-Id: I13dc5eab8835c4f3b95906816d42dccfeee8b092 Signed-off-by: Neale Ranns <nranns@cisco.com>
2018-09-11GBP Endpoint UpdatesNeale Ranns1-1/+2
- common types on the API - endpoints keyed in various ways for DP lookup - conparison functions for VPP IP address types Change-Id: If7ec0bbc5cea71fd0983fe78987d147ec1bd7ec8 Signed-off-by: Neale Ranns <neale.ranns@cisco.com>
2018-02-15Optimize GRE Tunnel and add support for ERSPAN encapJohn Lo1-2/+8
Change GRE tunnel to use the interface type where the same encap node is used as output node for all GRE tunnels, instead of having dedicated output and tx node for each tunnel. This allows for more efficient tunnel creation and deletion at scale tested at 1000's of GRE tunnels. Add support for ERSPAN encap as another tunnel type, in addition to the existing L3 and TEB types. The GRE ERSPAN encap supported is type 2 thus GRE encap need to include sequence number and GRE- ERSPAN tunnel can be created with user secified ERSPAN session ID. The GRE tunnel lookup hash key is updated to inclue tunnel type and session ID, in addition to SIP/DIP and FIB index. Thus, GRE-ERSPAN tunnel can be created, with the appropriate session ID, to be used as output interface for SPAN config to send mirrored packets. Change interface naming so that all GRE tunnels, irrespective of tunnel type, uses "greN" where N is the instance number. Removed interface reuse on tunnel creation and deletion to enable unfied tunnel interface name. Add support of user specified instance on GRE tunnel creation. Thus, N in the "greN" interface name can optionally be specified by user via CLI/API. Optimize GRE tunnel encap DPO stacking to bypass load-balance DPO node since packet output on GRE tunnel always belong to the same flow after 5-tupple hash. Change-Id: Ifa83915744a1a88045c998604777cc3583f4da52 Signed-off-by: John Lo <loj@cisco.com>
2017-12-16GRE tunnel key includes the FIB tableNeale Ranns1-0/+19
- GRE tunnels with the same src,dst addresses are not the same tunnel - Two data-plane improvements: - the cached key was never updated and so useless - no need to dereference the tunnel's HW interface to get the sw_if_index Change-Id: I2f2ea6e08c759a810b753cec22c497e921a2ca01 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-12-13GRE: fix single loop decap and add testNeale Ranns1-0/+25
Change-Id: I64e8a76a17057ae69de72a5a80c0a194cd0c21cb Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-09-11FIB table add/delete APINeale Ranns1-2/+6
part 2; - this adds the code to create an IP and MPLS table via the API. - but the enforcement that the table must be created before it is used is still missing, this is so that CSIT can pass. Change-Id: Id124d884ade6cb7da947225200e3bb193454c555 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-08-08L2 over MPLSNeale Ranns1-11/+13
[support for VPWS/VPLS] - switch to using dpo_proto_t rather than fib_protocol_t in fib_paths so that we can describe L2 paths - VLIB nodes to handle pop/push of MPLS labels to L2 Change-Id: Id050d06a11fd2c9c1c81ce5a0654e6c5ae6afa6e Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-04-05GRE over IPv6Ciara Loftus1-7/+142
Refactors the GRE node to work with both IPv4 and IPv6 transports. Note that this changes the binary configuration API to support both address families; each address uses the same memory for either address type and a flag to indicate which is in use. The CLI and VAT syntax remains unchanged; the code detects whether an IPv4 or an IPv6 address was given. Configuration examples: IPv4 CLI: create gre tunnel src 192.168.1.1 dst 192.168.1.2 IPv6 CLI: create gre tunnel src 2620:124:9000::1 dst 2620:124:9000::2 IPv4 VAT: gre_add_del_tunnel src 192.168.1.1 dst 192.168.1.2 IPv6 VAT: gre_add_del_tunnel src 2620:124:9000::1 dst 2620:124:9000::2 Change-Id: Ica8ee775dc101047fb8cd41617ddc8fafc2741b0 Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
2017-03-03Changing the IP table for an interface is an error if the interface already ↵Neale Ranns1-0/+4
has an address configured (VPP-601) Change-Id: I311fc264f73dd3b2b3ce9d7d1c33cd0515b36c4a Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-02-20Python test IP and MPLS objects conform to infra.Neale Ranns1-17/+19
Add IP[46] MFIB dump. Change-Id: I4a2821f65e67a5416b291e4912c84f64989883b8 Signed-off-by: Neale Ranns <nranns@cisco.com>
2016-12-23make test: improve handling of packet capturesKlement Sekera1-19/+14
Perform accounting of expected packets based on created packet infos. Use this accounting info to automatically expect (and verify) the correct number of packets to be captured. Automatically retry the read of the capture file if scapy raises an exception while doing so to handle rare cases when capture file is read while only partially written during busy wait. Don't fail assert_nothing_captured if only junk packets arrived. Change-Id: I16ec2e9410ef510d313ec16b7e13c57d0b2a63f5 Signed-off-by: Klement Sekera <ksekera@cisco.com>
2016-12-19make test: filter IPv6 RAs out by defaultKlement Sekera1-14/+1
Most of the test cases are not interested in IPv6 Router Alerts, so change the default behaviour of get_capture to filter out these packets with the possibility of turning the filtering off, for test cases which are interested in the RAs. Change-Id: I0b5ee685f82c49cd32c6d6a4638eb3493d2988fc Signed-off-by: Klement Sekera <ksekera@cisco.com>
2016-12-16make test: improve robustness and performanceKlement Sekera1-39/+23
Introduce an API which asserts empty capture for interface. Throw exception in old API if the capture does not exist, thus making it clear if the test expects packets to arrive or not. Improve performance by not doing sleeps after starting the packet generator, rather lazily deleting captures when needed. Fix wrong usage of packet.show() in various tests. Change-Id: I456cb23316eef99b3f35f80344fe595c4db9a21c Signed-off-by: Klement Sekera <ksekera@cisco.com>
2016-12-02MPLS infrastructure improvmentsNeale Ranns1-10/+11
- deprecate MPLSoEth and MPLSoGRE; replace with generic MPLS tunnel. - deprecates CLI 'mpls encap ..'; replace with addition of MPLS out label to a route/tunnel. - support for MPLS 'routes', e.g. MPLS x-connects. - deprecates CLI 'mpls decap ..'; replace with 'mpls route .. ' Change-Id: Ibda46544912f880d0200f22bf9ff9b52828fcc2f Signed-off-by: Neale Ranns <nranns@cisco.com>
2016-11-28GRE Tests update after postinit removalNeale Ranns1-1/+1
Change-Id: I33df256ca07c99149465c896c7063a3153021a5a Signed-off-by: Neale Ranns <nranns@cisco.com>
2016-11-22GRE tests and fixesNeale Ranns1-0/+700
Change-Id: I234240e9bdd4b69ad64a17b1449ae1e81c0edaca Signed-off-by: Neale Ranns <nranns@cisco.com>