summaryrefslogtreecommitdiffstats
path: root/test/vpp_papi_provider.py
AgeCommit message (Collapse)AuthorFilesLines
2018-01-23For DHCP client configuration control the setting of the broadcast flag in theNeale Ranns1-0/+2
DISCOVER message sent. According to RFC2131: In the case of a client using DHCP for initial configuration (before the client's TCP/IP software has been completely configured), DHCP requires creative use of the client's TCP/IP software and liberal interpretation of RFC 1122. The TCP/IP software SHOULD accept and forward to the IP layer any IP packets delivered to the client's hardware address before the IP address is configured; DHCP servers and BOOTP relay agents may not be able to deliver DHCP messages to clients that cannot accept hardware unicast datagrams before the TCP/IP software is configured. To work around some clients that cannot accept IP unicast datagrams before the TCP/IP software is configured as discussed in the previous paragraph, DHCP uses the 'flags' field [21]. The leftmost bit is defined as the BROADCAST (B) flag. The semantics of this flag are discussed in section 4.1 of this document. The remaining bits of the flags field are reserved for future use. They MUST be set to zero by clients and ignored by servers and relay agents. Figure 2 gives the format of the 'flags' field. this changes means VPP conforms to the: "SHOULD accept and forward to the IP layer any IP packets delivered to the client's hardware address before the IP address is configured" with the caveat that VPP allows DHCP packets destined to the stanard client DHCP port to be delivered. With this enhancement the control-plane is now able to choose the setting of the broadcast flag. Change-Id: Ia4eb2c9bb1e30c29f9192facc645e9533641955a Signed-off-by: Neale Ranns <nranns@cisco.com>
2018-01-22NAT44: asymmetrical static mapping rule (VPP-1135)Matus Fabian1-1/+4
add option to NAT44 static mapping API/CLI to make rule asymmetrical (rule match only out2in direction) Change-Id: If262a3ff375a24d3059f0de1f1ac387a4fe09475 Signed-off-by: Matus Fabian <matfabia@cisco.com>
2018-01-11NAT44: asymmetrical load balancing static mapping rule (VPP-1132)Matus Fabian1-0/+2
Add option to NAT44 load balancing static mapping API/CLI to make rule asymmetrical (rule match only in out2in direction). Change-Id: I325ecef5591e4bf44ce4469a24d44fe56c3bb2e9 Signed-off-by: Matus Fabian <matfabia@cisco.com>
2018-01-11Add basic support for DS-Lite CE (VPP-1059)Juraj Sloboda1-0/+11
Change-Id: Ifcca60da3f77c0a4959f98b3365c846badbdc2d0 Signed-off-by: Juraj Sloboda <jsloboda@cisco.com>
2018-01-09DVR: run L3 output featuresNeale Ranns1-3/+3
- rename l2_bridged to is_dvr. Including on the ip.api this was new in the 18.01 release so no compatability issues. - steal the free space in vnet_buffer_opaque_t for use with flags. - run the ipX-output feature arc from the DVR DPO Change-Id: I040e5976d1dbe076fcdda3a40a7804f56337ce3f Signed-off-by: Neale Ranns <nranns@cisco.com>
2018-01-05Add support for 464XLAT NAT44 mode (VPP-1045)Juraj Sloboda1-0/+2
Change-Id: I24e7a26972bbbfcea100292b212b29ae7a349335 Signed-off-by: Juraj Sloboda <jsloboda@cisco.com>
2017-12-22tcp: add builtin server/client transfer testFlorin Coras1-0/+15
Change-Id: Iab0baabf2f27bc7ad7fbf2d2789a493752b07d8a Signed-off-by: Florin Coras <fcoras@cisco.com>
2017-12-20L2 EmulationNeale Ranns1-0/+12
L2 Emulation is a feautre that is applied to L2 ports to 'extract' IP packets from the L2 path and inject them into the L3 path (i.e. into the appropriate ip[4|6]_input node). L3 routes in the table_id for that interface should then be configured as DVR routes, therefore the forwarded packet has the L2 header preserved and togehter the L3 routed system behaves like an L2 bridge. Change-Id: I8effd7e2f4c67ee277b73c7bc79aa3e5a3e34d03 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-12-20Translate matching packets using NAT (VPP-1069)Juraj Sloboda1-0/+11
Add API function which enables forwarding of packets not matching existing translation or static mapping instead of dropping them. When forwarding is enabled matching packets will be translated while non-matching packets will be forwarded without translation. Change-Id: Ic13040cbad16d3a1ecdc3e02a497171bef6aa413 Signed-off-by: Juraj Sloboda <jsloboda@cisco.com>
2017-12-19NAT: Twice NAT44 (VPP-969)Matus Fabian1-4/+18
Translation of both source and destination addresses and ports for 1:1 NAT session initiated from outside network (ExternalIP K8 use case). Change-Id: Ic0000497cf71619aac996d6d580844f0ea0edc14 Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-12-15ESP_AH_test_automation_scripts rev1“mystarrocks”1-0/+162
Change-Id: I941abdc4a02e4c52c66b9d299e380b27caca7c1d Signed-off-by: “mystarrocks” <mystarrocks@yahoo.com>
2017-12-12tcp/session: add make testsFlorin Coras1-0/+5
Change-Id: Icb93ab80c5a6432d7b2b698a47e8b612c6f06fbd Signed-off-by: Florin Coras <fcoras@cisco.com>
2017-12-09BIER in non-MPLS netowrksNeale Ranns1-10/+14
as decsribed in section 2.2 ihttps://tools.ietf.org/html/draft-ietf-bier-mpls-encapsulation-10 with BIFT encoding from: https://tools.ietf.org/html/draft-wijnandsxu-bier-non-mpls-bift-encoding-00 changes: 1 - introduce the new BIFT lookup table. BIER tables that have an associated MPLS label are added to the MPLS-FIB. Those that don't are added to the BIER table 2 - BIER routes that have no associated output MPLS label will add a BIFT label. 3 - The BIER FMask has a path-list as a member to resolve via any possible path. Change-Id: I1fd4d9dbd074f0e855c16e9329b81460ebe1efce Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-11-30NAT44: identity NAT (VPP-1073)Matus Fabian1-0/+35
Identity mapping translate an IP address to itself. Change-Id: Icc0ca5102d32547a4b0c75720b5f5bf41ed69c71 Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-11-16Add Support of DHCP VSS Type 0 where VPN-ID is ASCIIJohn Lo1-5/+9
Enhence support of DHCP VSS (Virtual Subnet Selection) to include VSS type 0 where VSS info is a NVT (Network Virtual Terminal) ASCII VPN ID where the ASCII string MUST NOT be terminated with a zero byte. Existing code already support VSS type 1, where VSS information is a RFC 2685 VPN-ID of 7 bytes with 3 bytes OUI and 4 bytes VPN index, and VSS type 255 indicating global VPN. Change-Id: I54edbc447c89a2aacd1cc9fc72bd5ba386037608 Signed-off-by: John Lo <loj@cisco.com>
2017-11-10add classify session action set-sr-policy-indexGabriel Ganne1-0/+10
This allows to use the classifier to steer source routing packets instead of using the "sr steer" command. This way we can steer on anything instead of only the dst ip address. test: * add add_node_next function to the VppPapiProvider class. * add simple test scenario using the classifier to steer packets with dest ip addr == a7::/8 to the source routing insert node. * use new interface indexes (3,4) instead of (0,1) to prevent a cleanup conflict with the other tests which attach a specific fib to the interface. The test creates interfaces sepsrated from the other tests to prevent a conflict in the cleaning of the ip6 fib index 1 which causes vpp not to be able to find a default route on this table. Change-Id: Ibacb30fab3ce53f0dfe848ca6a8cdf0d111d8336 Signed-off-by: Gabriel Ganne <gabriel.ganne@enea.com>
2017-11-09BIERNeale Ranns1-0/+119
- see draft-ietf-bier-mpls-encapsulation-10 - midpoint, head and tail functions - supported payload protocols; IPv4 and IPv6 only. Change-Id: I59d7363bb6fdfdce8e4016a68a9c8f5a5e5791cb Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-11-08ACL plugin support tagged subinterfacesPavel Kotucek1-0/+17
Change-Id: I92b351895c7efb26533c05512b91ead8ddbfb9c8 Signed-off-by: Pavel Kotucek <pkotucek@cisco.com>
2017-11-08NAT64 to use IPv4 address from interface (VPP-1051)Matus Fabian1-0/+12
Change-Id: I326429c31dea6958a342ee152ef86cb975f4b12c Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-11-07SNAT: IP fragmentation (VPP-890)Matus Fabian1-0/+37
Translation of fragmented packets. Change-Id: I9b1f2e9433ce273638080f32c2d3bff39c49899d Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-11-07UDP Encapsulation.Neale Ranns1-0/+39
A UDP-encap object that particiapates in the FIB graph and contributes DPO to teh output chain. It thereofre resembles a tunnel but without the interface. FIB paths (and henace routes) can then be created to egress through the UDP-encap. Said routes can have MPLS labels, hence this also allows MPLSoUPD. Encap is uni-directional. For decap, one still registers with the UDP port dispatcher. Change-Id: I23bd345523b20789a1de1b02022ea1148ca50797 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-11-07NAT: DS-Lite (VPP-1040)Matus Fabian1-0/+28
Dual-Stack Lite enables a broadband service provider to share IPv4 addresses among customers by combining two well-known technologies: IPv4-in-IPv6 and NAT. Change-Id: I039740f8548c623cd1ac89b8ecda1a6cc4aafb9c Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-10-31l2fib: MAC: Fix uint64 to u8 byte arrayMohsin Kazmi1-1/+1
As per proposal on the mailing list, this patch fixes the represntation of MAC address in VPP API calls for · L2fib_add_del · L2_fib_table_details Change-Id: I31e17efd1a6314cded69666e693cb8fc33158d02 Signed-off-by: Mohsin Kazmi <sykazmi@cisco.com>
2017-10-26NAT: delete session API/CLI (VPP-1041)Matus Fabian1-0/+23
Administratively delete NAT44 session for specific inside/outside addresses and port pair. Change-Id: If5ab500ac3592c7153d6d8f2cc0297df7309fbc3 Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-10-25VPP-1033: Python API support arbitrary sized input parameters.Ole Troan1-2/+2
Dynamically calculate the required buffer size to pack into based on message definition. Also add input parameter length checking. Change-Id: I7633bec596e4833bb328fbf63a65b866c7985de5 Signed-off-by: Ole Troan <ot@cisco.com>
2017-10-19Remove unused 'not_last' parameter from ip_add_del_routeMarek Gradzki1-7/+2
Vat supports setting value for the parameter, but 'not_last' is ignored by ip_add_del_route handler, so can be removed. This patch - updates ip.api, - removes vat handlers - updates vpp_papi_provider.py (also mpls_route_add_del with unused not_last) Change-Id: Ife15de123db4bc8247103a29b90bce1988e46534 Signed-off-by: Marek Gradzki <mgradzki@cisco.com>
2017-10-14Source Lookup progammable via APINeale Ranns1-0/+4
Change-Id: I5d5d4f22b6369d504455a644f73076d772fbcfb4 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-10-10punt and drop features:Neale Ranns1-0/+57
- new IPv4 and IPv6 feature arcs on the punt and drop nodes - new features: - redirect punted traffic to an interface and nexthop - police punted traffic. Change-Id: I53be8bf4e06545add8a3619e462de5ffedd0a95c Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-10-06Initial GENEVE TUNNEL implementation and tests.Marco Varlese1-0/+32
Notes on this first implementation: * First version of the implementation does NOT support GENEVE OPTIONS HEADER: it isn't well understood what the purpose of the OPTIONS will be and/or what content would be placed in the variable option data; Once the IETF work will evolve and further information will be available it could be possible to modify the frame rewrite to contemplate the actual GENEVE OPTIONS. Change-Id: Iddfe6f408cc45bb0800f00ce6a3e302e48a4ed52 Signed-off-by: Marco Varlese <marco.varlese@suse.com>
2017-10-05Distributed Virtual Router SupportNeale Ranns1-0/+2
A distributed virtual router works by attmpeting to switch a packet, but on failing to find a local consumer (i.e. the packet is destined to a locally attached host) then the packet is sent unmodified 'upstream' to where the rest of the 'distributed' router is present. When L3 switching a packet this means the L2 header must not be modifed. This patch adds a 'l2-bridge' object to the L3 FIB which re-injects packets from the L3 path back into the L2 path - use with extreme caution. Change-Id: I069724eb45956647d7980cbe40a80a788ee6ee82 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-10-02L2-FIB:add mac learn events testEyal Bari1-0/+9
fixes an issue where events were not sent if BD doesn't enable mac aging Change-Id: Iddc53cb5c45e560633e6c5cff2731dccfc70ad5b Signed-off-by: Eyal Bari <ebari@cisco.com>
2017-09-27acl-plugin: take 2 at VPP-991 fix, this time with a test case which verifies it.Andrew Yourtchenko1-0/+10
The replacement of [] with pool_elt_at_index and subsequent fixing it was incorrect - it was equivalent to &[], since it returns a pointer to the element. I've added VPP-993 previously to create a testcase, so this commit partially fulfills that one as well. Change-Id: I5b15e3ce48316f0429232aacf885e8f7c63d9522 Signed-off-by: Andrew Yourtchenko <ayourtch@gmail.com>
2017-09-26acl-plugin: test: move the API calls to vpp_papi_provider.pyAndrew Yourtchenko1-0/+29
Change-Id: I1d3818027b8a1fcb1ec12016e3476b5c22a2d5a5 Signed-off-by: Andrew Yourtchenko <ayourtch@gmail.com>
2017-09-22IP-MAC,ND:wildcard events,fix sending multiple eventsEyal Bari1-0/+6
wildcard ND events publisher was sending the last event mutiple times Change-Id: I6c30f2de03fa825e79df9005a3cfaaf68ff7ea2f Signed-off-by: Eyal Bari <ebari@cisco.com>
2017-09-18L2BD,ARP-TERM:fix arp query report mechanism+testEyal Bari1-3/+9
previous mechanism was emitting duplicates of last event, when handling multiple arp queries. tests: * arp events sent for graps * duplicate suppression * verify no events when disabled Change-Id: I84adc23980d43b819261eccf02ec056b5cec61df Signed-off-by: Eyal Bari <ebari@cisco.com>
2017-09-12ACL-plugin add "replace" semantics for adding a new MacIP aclPavel Kotucek1-6/+14
Change-Id: Ia5c869b2d8b8ad012b9e89fb6720c9c32d9ee065 Signed-off-by: Pavel Kotucek <pkotucek@cisco.com>
2017-09-11FIB table add/delete APINeale Ranns1-12/+34
part 2; - this adds the code to create an IP and MPLS table via the API. - but the enforcement that the table must be created before it is used is still missing, this is so that CSIT can pass. Change-Id: Id124d884ade6cb7da947225200e3bb193454c555 Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-09-08ACL-plugin MACIP ACLs testsPavel Kotucek1-0/+55
Change-Id: Ie40c837358454cfe9475cb2c14fdf20b24fa6602 Signed-off-by: Pavel Kotucek <pkotucek@cisco.com>
2017-09-06NAT: Destination NAT44 with load-balancing (VPP-954)Matus Fabian1-0/+30
added load-balancing static mappings with unequal load support Change-Id: Ie505e41f24d46f812b94dd28bdafe3dc170a6060 Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-08-23NAT: Rename snat plugin to nat (VPP-955)Matus Fabian1-100/+87
Change-Id: I30a7e3da7a4efc6038a91e27b48045d4b07e2764 Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-08-22SRv6 testsKris Michielsen1-0/+118
Change-Id: Ib1d2fc5a83d9d007a0468591a73881675f1bec9b Signed-off-by: Kris Michielsen <kmichiel@cisco.com>
2017-08-16SNAT: Make proto optional in nat64_bib_dump (VPP-942)Matus Fabian1-4/+4
make proto optional in nat64_bib_dump and nat64_st_dump Change-Id: Idd102ce2b1555d38783fd22c84e46b4c48570edc Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-08-11Dedicated SW Interface EventNeale Ranns1-7/+2
Change-Id: I06a10a4291e61aec3f1396d2514ed6fe3901897a Signed-off-by: Neale Ranns <neale.ranns@cisco.com> Signed-off-by: Marek Gradzki <mgradzki@cisco.com>
2017-08-09Add PPPoE PluginHongjun Ni1-0/+26
Supports 64K PPPoE sessions This plugin adds three graph nodes: 1) pppoe-input for PPPoE decapsulation 2) pppoe-encap for PPPoE encapsulation 3) pppoe-tap-dispatch for control plane process Below is the configuration to make PPPoE CP and DP work: vim /etc/vpp/startup.conf tuntap { enable ethernet name newtap } create pppoe tap tap-if-index 1 //Configure it after a subscriber's PPPoE discovery and PPP link establishment succeeds: create pppoe session client-ip 100.1.2.1 session-id 1 client-mac 00:11:01:00:00:01 show pppoe fib show pppoe session Change-Id: I73e724b6bf7c3e4181a9914c5752da1fa72d7e60 Signed-off-by: Hongjun Ni <hongjun.ni@intel.com>
2017-08-08L2 over MPLSNeale Ranns1-2/+2
[support for VPWS/VPLS] - switch to using dpo_proto_t rather than fib_protocol_t in fib_paths so that we can describe L2 paths - VLIB nodes to handle pop/push of MPLS labels to L2 Change-Id: Id050d06a11fd2c9c1c81ce5a0654e6c5ae6afa6e Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-08-01P2P EthernetPavel Kotucek1-0/+25
Change-Id: Idb97e573961b3bc2acdeef77582314590795f8c3 Signed-off-by: Pavel Kotucek <pkotucek@cisco.com>
2017-07-24SPAN:add l2 mirrorEyal Bari1-2/+5
added span feature nodes for l2-input / l2-output Change-Id: Ib6e0ce60d0811901b6edd70209e6a4c4a35cd8ff Signed-off-by: Eyal Bari <ebari@cisco.com>
2017-07-20SNAT: in2out translation as an output feature (VPP-903)Matus Fabian1-0/+23
in2out translation as an output feature on the outside interface (postrouting) Change-Id: I32c0311be09bdf102b9a0885b8b89c7588cb558f Signed-off-by: Matus Fabian <matfabia@cisco.com>
2017-07-18DHCP client option 61 "client_id"Neale Ranns1-0/+2
the existing seeting of client_id to a VPP version number was unused and so overridden Change-Id: If9ebea936336f1fcca8d07e67186c95f8f8f0ccd Signed-off-by: Neale Ranns <nranns@cisco.com>
2017-07-18DHCP client - remove interface address when DHCP de-configuredNeale Ranns1-0/+15
Change-Id: I63c59e3c13859b51999d283774f7783ef0a6a5ed Signed-off-by: Neale Ranns <nranns@cisco.com>