blob: 69063582dcf633b9828e48894b65151be2c43b02 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
|
.. _interface:
.. toctree::
Set Interface Commands
=======================
This section covers those commands that are related to setting an interface:
* `Set Interface`_
* `Set Interface IP Address`_
* `Set Interface L2 Bridge`_
* `Set Interface MTU`_
* `Set Interface Promiscuous`_
* `Set Interface State`_
.. note:: For a complete list of CLI Debug commands refer to the Debug CLI section of the `Source Code Documents <https://docs.fd.io/vpp/18.07/clicmd.html>`_ .
Set Interface
++++++++++++++++
Summary/Usage
-------------
Interface commands.
Declaration and Implementation
-------------------------------
**Declaration:** vnet_cli_set_interface_command (src/vnet/interface_cli.c line 484)
Set Interface IP Address
+++++++++++++++++++++++++
Summary/Usage
-------------
set interface ip address [del] <*interface*> <*ip-addr*>/<*mask*> | [all]
Description
-------------
Add an IP Address to an interface or remove and IP Address from an interface.
The IP Address can be an IPv4 or an IPv6 address. Interfaces may have multiple IPv4 and IPv6
addresses. There is no concept of primary vs. secondary interface addresses; they're just addresses.
To display the addresses associated with a given interface, use the command **show interface address** <*interface*>.
.. note::
The debug CLI does not enforce classful mask-width / addressing constraints.
Example Usage
--------------
An example of how to add an IPv4 address to an interface:
.. code-block:: console
vpp# set interface ip address GigabitEthernet2/0/0 172.16.2.12/24
An example of how to add an IPv6 address to an interface:
.. code-block:: console
vpp# set interface ip address GigabitEthernet2/0/0 ::a:1:1:0:7/126
To delete a specific interface ip address:
.. code-block:: console
vpp# set interface ip address GigabitEthernet2/0/0 172.16.2.12/24 del
To delete all interfaces addresses (IPv4 and IPv6):
.. code-block:: console
vpp# set interface ip address GigabitEthernet2/0/0 del all
Declaration and Implementation
-------------------------------
**Declaration:** set_interface_ip_address_command (src/vnet/ip/ip46_cli.c line 216)
**Implementation:** add_del_ip_address
Set Interface L2 Bridge
+++++++++++++++++++++++++
Summary/Usage
-------------
set interface l2 bridge <*interface*> <*bridge-domain-id*> [bvi|uu-fwd] [shg]
Description
-------------
Use this command put an interface into Layer 2 bridge domain. If a bridge-domain with the provided
bridge-domain-id does not exist, it will be created. Interfaces in a bridge-domain forward packets
to other interfaces in the same bridge-domain based on destination mac address. To remove an interface
from a the Layer 2 bridge domain, put the interface in a different mode, for example Layer 3 mode.
Optionally, an interface can be added to a Layer 2 bridge-domain as a Bridged Virtual Interface (bvi).
Only one interface in a Layer 2 bridge-domain can be a bvi.
Optionally, a split-horizon group can also be specified. This defaults to 0 if not specified.
Example Usage
--------------
Example of how to configure a Layer 2 bridge-domain with three interfaces (where 200 is the bridge-domain-id):
.. code-block:: console
vpp# set interface l2 bridge GigabitEthernet0/8/0.200 200
This interface is added a BVI interface:
.. code-block:: console
vpp# set interface l2 bridge GigabitEthernet0/9/0.200 200 bvi
This interface also has a split-horizon group of 1 specified:
.. code-block:: console
vpp# set interface l2 bridge GigabitEthernet0/a/0.200 200 1
Example of how to remove an interface from a Layer2 bridge-domain:
.. code-block:: console
vpp# set interface l3 GigabitEthernet0/a/0.200
Declaration and Implementation
-------------------------------
**Declaration:** int_l2_bridge_cli (src/vnet/l2/l2_input.c line 949)
**Implementation:** int_l2_bridge
Set Interface MTU
++++++++++++++++++
Summary/Usage
-------------
.. code-block:: shell
set interface mtu [packet|ip4|ip6|mpls] <value> <interface>
Set Interface Promiscuous
++++++++++++++++++++++++++
Summary/Usage
-------------
.. code-block:: shell
set interface promiscuous [on|off] <interface>.
.. _setintstate:
Set Interface State
++++++++++++++++++++
This command is used to change the admin state (up/down) of an
interface.
If an interface is down, the optional *punt* flag can also be set. The
*punt* flag implies the interface is disabled for forwarding but punt
all traffic to slow-path. Use the *enable* flag to clear *punt* flag
(interface is still down).
Summary/Usage
-------------
.. code-block:: shell
set interface state <interface> [up|down|punt|enable].
Example Usage
----------------
Example of how to configure the admin state of an interface to **up**:
.. code-block:: console
vpp# set interface state GigabitEthernet2/0/0 up
Example of how to configure the admin state of an interface to **down**:
.. code-block:: console
vpp# set interface state GigabitEthernet2/0/0 down
|
