blob: 82dba96c171a0d4374d7937140f1b807f5945230 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
|
Stateless Traffic Gen with VPP
==============================
It’s simple to configure vpp as a high-performance stateless traffic
generator. A couple of vpp worker threads running on an older system can
easily generate 20 MPPS’ worth of traffic.
In the configurations shown below, we connect a vpp traffic generator
and a vpp UUT using two 40 gigabit ethernet ports on each system:
::
+-------------------+ +-------------------+
| traffic generator | | UUT |
| port 0 | <=======> | port 0 |
| 192.168.40.2/24 | | 192.168.40.1/24 |
+-------------------+ +-------------------+
+-------------------+ +-------------------+
| traffic generator | | UUT |
| port 1 | <=======> | port 1 |
| 192.168.41.2/24 | | 192.168.41.1/24 |
+-------------------+ +-------------------+
Traffic Generator Setup Script
------------------------------
::
set int ip address FortyGigabitEthernet2/0/0 192.168.40.2/24
set int ip address FortyGigabitEthernet2/0/1 192.168.41.2/24
set int state FortyGigabitEthernet2/0/0 up
set int state FortyGigabitEthernet2/0/1 up
comment { send traffic to the VPP UUT }
packet-generator new {
name worker0
worker 0
limit 0
rate 1.2e7
size 128-128
tx-interface FortyGigabitEthernet2/0/0
node FortyGigabitEthernet2/0/0-output
data { IP4: 1.2.40 -> 3cfd.fed0.b6c8
UDP: 192.168.40.10 -> 192.168.50.10
UDP: 1234 -> 2345
incrementing 114
}
}
packet-generator new {
name worker1
worker 1
limit 0
rate 1.2e7
size 128-128
tx-interface FortyGigabitEthernet2/0/1
node FortyGigabitEthernet2/0/1-output
data { IP4: 1.2.4 -> 3cfd.fed0.b6c9
UDP: 192.168.41.10 -> 192.168.51.10
UDP: 1234 -> 2345
incrementing 114
}
}
comment { delete return traffic on sight }
ip route add 192.168.50.0/24 via drop
ip route add 192.168.51.0/24 via drop
Note 1: the destination MAC addresses shown in the configuration (e.g.
3cfd.fed0.b6c8 and 3cfd.fed0.b6c9) **must** match the vpp UUT port MAC
addresses.
Note 2: this script assumes that /etc/vpp/startup.conf and/or the
command-line in use specifies (at least) two worker threads. Uncomment
“workers 2” in the cpu configuration section of /etc/vpp/startup.conf:
::
## Specify a number of workers to be created
## Workers are pinned to N consecutive CPU cores while skipping "skip-cores" CPU core(s)
## and main thread's CPU core
workers 2
Any plausible packet generator script - including one which replays pcap
captures - can be used.
UUT Setup Script
----------------
The vpp UUT uses a couple of static routes to forward traffic back to
the traffic generator:
::
set int ip address FortyGigabitEthernet2/0/0 192.168.40.1/24
set int ip address FortyGigabitEthernet2/0/1 192.168.41.1/24
set int state FortyGigabitEthernet2/0/0 up
set int state FortyGigabitEthernet2/0/1 up
ip route add 192.168.50.10/32 via 192.168.41.2
ip route add 192.168.51.10/32 via 192.168.40.2
|
