blob: a2748cadca76df3d76a460d611a2138725f5677a (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
|
## Development performance test {#libmemif_devperftest_doc}
Simle test cases using ICMP. icmpr-epoll example app generates and transmits packets over memif interface.
#### TC1: LIB-VPP
Start icmpr-epoll example app and VPP.
VPP-side config:
```
DBGvpp# create interface memif id 0 master
DBGvpp# set int state memif0/0 up
DBGvpp# set int ip address memif0/0 192.168.1.1/24
```
icmpr-epoll:
```
conn 0 0 1
```
> Last argument specifies interrupt function to use. This function only responds to ARP requests. This is important because, packet generation and transmitting is handled by a separate thread. Calling memif_tx_burst from multiple threads writing on same queue could transmit uninitialized buffers.
Once connection is established, you can send ping from VPP to icmpr-epoll app to learn its mac address.
```
DBGvpp# ping 192.168.1.2
```
> There should be no ICMP response. Only ARP response.
Now send ICMP requests from icmpr-epoll:
```
send <index> <num-of-packets> <ip_daddr> <hw_daddr>
send 0 5 192.168.1.1 02:fe:ff:ff:ff:ff
```
this command will create new thread which will generate icmp packets and transmit them over memif connection with specified index. Once the sequence is finished status will be printed.
###### Example results (owerview of test data)
(This test was run with modofication in VPP-memif plugin. The modification disallows memif tx node to allocate last ring buffer)
lib-tx: 200M (if ring full don't drop packets)
vpp-rx: 200M
vpp-tx: 200M - 50K (if ring full drop packets)
lib-rx: =vpp-tx
drop: ~0.025% (full ring)
pps: ~650K
multiple interfaces:
pps: divided
drop: constant
#### TC2: LIB-LIB
This test case will not drop packets if memif ring is full. Instead it will loop until all required packets have been sent.
Start two instances of icmpr-epoll example app.
instance 1:
```
conn 0 1 0
```
instance 2:
```
conn 0 0 1
send 0 5 192.168.1.1 aa:aa:aa:aa:aa:aa
```
> icmpr-epoll example app doesn't check ip or mac address so as long as the format is correct you can type anything as ip_daddr and hw_daddr arguments.
###### Example results (owerview of test data)
lib1-tx: 200M (if ring full don't drop packets)
lib2-rx: 200M
lib2-tx: 200M (if ring full don't drop packets)
lib1-rx: 200M
drop: obsolete
pps: 4.5M
multiple interfaces:
not tested (excpected same as TC1)
#### TC3: LIB-LIB
Start two instances of icmpr-epoll example app.
instance 1:
```
conn 0 1
```
instance 2:
```
conn 0 0 1
send 0 5 192.168.1.1 aa:aa:aa:aa:aa:aa
```
###### Example results (owerview of test data)
lib1-tx: 200M (if ring full don't drop packets)
lib2-rx: 200M
lib2-tx: 169626182 (if ring full drop packets)
lib1-rx: =lib2-tx
drop: ~15%
pps: ~6M
multiple interfaces:
not tested (excpected same as TC1)
|
