blob: f94467dade187aef96037dccb50ab7fd2cd68d98 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
|
# Stateful NAT64: Network Address and Protocol Translation from IPv6 Clients to IPv4 Servers {#nat64_doc}
## Introduction
Stateful NAT64 in VPP allows IPv6-only clients to contact IPv4 servers using unicast UDP, TCP, or ICMP based on RFC 6146.
## Configuration
### Enable/disable NAT64 feature on the interface
> set interface nat64 in|out <intfc> [del]
in: inside/local/IPv6 network
out: outside/external/IPv4 network
intfc: interface name
### Add/delete NAT64 pool address
One or more public IPv4 addresses assigned to a NAT64 are shared among several IPv6-only clients.
> nat64 add pool address <ip4-range-start> [- <ip4-range-end>] [tenant-vrf <tenant-vrf-id>] [del]
ip4-range-start: First IPv4 address of the range
ip4-range-end: Last IPv4 address of the range (optional, not used for single address)
tenant-vrf-id: VRF id of the tenant associated with the pool address (optional, if not set pool address is global)
### Add/delete static BIB entry
Stateful NAT64 also supports IPv4-initiated communications to a subset of the IPv6 hosts through staticaly configured bindings.
> nat64 add static bib <ip6-addr> <in-port> <ip4-addr> <out-port> tcp|udp|icmp [vfr <table-id>] [del]
ip6-addr: inside IPv6 address of the host
in-port: inside port or ICMPv6 identifier
ip4-addr: outside IPv4 address of the host
out-port: outside port or ICMPv4 identifier
table-id: VRF id of the tenant associated with the BIB entry (optional, default use global VRF)
### Set NAT64 session timeouts
Session is deleted when timer expires. If all sessions corresponding to a dynamically create BIB entry are deleted, then the BIB entry is also deleted. When packets are flowing sessiom timer is refreshed to keep the session alive.
> set nat64 timeouts udp <sec> icmp <sec> tcp-trans <sec> tcp-est <sec> tcp-incoming-syn <sec> | reset
udp: UDP session timeout value (default 300sec)
icmp: ICMP session timeout value (default 60sec)
tcp-trans: transitory TCP session timeout value (default 240sec)
tcp-est: established TCP session timeout value (default 7440sec)
tcp-incoming-syn: incoming SYN TCP session timeout value (default 6sec)
reset: reset timers to default values
### Set NAT64 prefix
Stateful NAT64 support the algorithm for generating IPv6 representations of IPv4 addresses defined in RFC 6052. If no prefix is configured, Well-Known Prefix (64:ff9b::/96) is used.
> nat64 add prefix <ip6-prefix>/<plen> [tenant-vrf <vrf-id>] [del]
ip6-prefix: IPv6 prefix
plen: prefix length (valid values: 32, 40, 48, 56, 64, or 96)
tenant-vrf: VRF id of the tenant associated with the prefix
### Show commands
> show nat64 pool
> show nat64 interfaces
> show nat64 bib tcp|udp|icmp
> show nat64 session table tcp|udp|icmp
> show nat64 tiemouts
> show nat64 prefix
## Notes
Multi thread is not supported yet (CLI/API commands are disabled when VPP runs with multiple threads).
|
