diff options
Diffstat (limited to 'tests/vpp')
20 files changed, 3873 insertions, 0 deletions
diff --git a/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.robot b/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.robot new file mode 100644 index 0000000000..d3aefb6fae --- /dev/null +++ b/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.robot @@ -0,0 +1,156 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | MEMIF | LXC +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-X520-DA2 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with two L2 +| ... | bridge domains and MAC learning enabled. LXC is connected to VPP via +| ... | Memif interface. LXC is running same VPP version as running on DUT. LXC +| ... | is limited via cgroup to use 3 cores allocated from pool of isolated +| ... | CPUs. There are no memory constraints. DUT1 and DUT2 tested with +| ... | 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | LXC +| ${container_image}= | ${EMPTY} +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${3} + +*** Keywords *** +| Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread(s), ${wt}\ +| | ... | phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 Bridge Domain for '1' memif pairs in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc03-1518B-1t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=${1518} | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate forIMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc06-1518B-2t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=${1518} | wt=2 | rxq=1 diff --git a/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-2memif-1dcr-mrr.robot b/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-2memif-1dcr-mrr.robot new file mode 100644 index 0000000000..5c5062424a --- /dev/null +++ b/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-2memif-1dcr-mrr.robot @@ -0,0 +1,156 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-X520-DA2 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results L2XC test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | Container is connected to VPP via Memif interface. Container is running +| ... | same VPP version as running on DUT. Container is limited via cgroup to +| ... | use 3 cores allocated from pool of isolated CPUs. There are no memory +| ... | contraints. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${3} + +*** Keywords *** +| Check RR for l2xcbase-eth-2memif-1dcr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread(s), ${wt}\ +| | ... | phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect for '1' memif pairs in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-eth-2memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1dcr +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-IMIX-1t1c-eth-l2xcbase-eth-2memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1dcr +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc03-1518B-1t1c-eth-l2xcbase-eth-2memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1dcr +| | framesize=${1518} | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2xcbase-eth-2memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1dcr +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-IMIX-2t2c-eth-l2xcbase-eth-2memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate forIMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1dcr +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc06-1518B-2t2c-eth-l2xcbase-eth-2memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1dcr +| | framesize=${1518} | wt=2 | rxq=1 diff --git a/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-2memif-1lxc-mrr.robot b/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-2memif-1lxc-mrr.robot new file mode 100644 index 0000000000..4b347b478d --- /dev/null +++ b/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-2memif-1lxc-mrr.robot @@ -0,0 +1,155 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | MEMIF | LXC +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-X520-DA2 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results L2XC test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | LXC is connected to VPP via Memif interface. LXC is running same VPP +| ... | version as running on DUT. LXC is limited via cgroup to use 3 cores +| ... | allocated from pool of isolated CPUs. There are no memory contraints. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | LXC +| ${container_image}= | ${EMPTY} +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${3} + +*** Keywords *** +| Check RR for l2xcbase-eth-2memif-1lxc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread(s), ${wt}\ +| | ... | phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect for '1' memif pairs in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-IMIX-1t1c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc03-1518B-1t1c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=${1518} | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-IMIX-2t2c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate forIMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc06-1518B-2t2c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=${1518} | wt=2 | rxq=1 diff --git a/tests/vpp/perf/container_memif/40ge2p1xl710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.robot b/tests/vpp/perf/container_memif/40ge2p1xl710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.robot new file mode 100644 index 0000000000..a167ae4e9e --- /dev/null +++ b/tests/vpp/perf/container_memif/40ge2p1xl710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.robot @@ -0,0 +1,160 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-XL710 | ETH | L2BDMACLRN | BASE | MEMIF | LXC +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-XL710 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with two L2 +| ... | bridge domains and MAC learning enabled. LXC is connected to VPP via +| ... | Memif interface. LXC is running same VPP version as running on DUT. LXC +| ... | is limited via cgroup to use 3 cores allocated from pool of isolated +| ... | CPUs. There are no memory constraints. DUT1 and DUT2 tested with +| ... | 2p40GE NIC XL710 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | LXC +| ${container_image}= | ${EMPTY} +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${3} + +*** Keywords *** +| Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread(s), ${wt}\ +| | ... | phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${get_framesize} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 Bridge Domain for '1' memif pairs in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc03-1518B-1t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=${1518} | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate forIMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc06-1518B-2t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | [Template] | Check RR for l2bdbasemaclrn-eth-2memif-1lxc +| | framesize=${1518} | wt=2 | rxq=1 diff --git a/tests/vpp/perf/container_memif/40ge2p1xl710-eth-l2xcbase-eth-2memif-1lxc-mrr.robot b/tests/vpp/perf/container_memif/40ge2p1xl710-eth-l2xcbase-eth-2memif-1lxc-mrr.robot new file mode 100644 index 0000000000..e0964741b6 --- /dev/null +++ b/tests/vpp/perf/container_memif/40ge2p1xl710-eth-l2xcbase-eth-2memif-1lxc-mrr.robot @@ -0,0 +1,159 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-XL710 | ETH | L2XCFWD | BASE | MEMIF | LXC +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-XL710 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results L2XC test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel. +| ... | LXC is connected to VPP via Memif interface. LXC is running same VPP +| ... | version as running on DUT. LXC is limited via cgroup to use 3 cores +| ... | allocated from pool of isolated CPUs. There are no memory contraints. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | LXC +| ${container_image}= | ${EMPTY} +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${3} + +*** Keywords *** +| Check RR for l2xcbase-eth-2memif-1lxc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread(s), ${wt}\ +| | ... | phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${get_framesize} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect for '1' memif pairs in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-IMIX-1t1c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc03-1518B-1t1c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=${1518} | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-IMIX-2t2c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate forIMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc06-1518B-2t2c-eth-l2xcbase-eth-2memif-1lxc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | [Template] | Check RR for l2xcbase-eth-2memif-1lxc +| | framesize=${1518} | wt=2 | rxq=1 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot new file mode 100644 index 0000000000..b3c1eb3d06 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot @@ -0,0 +1,211 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | DOT1Q | L2BDMACLRN | BASE | VHOST | 1VM +| ... | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2BD test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. 802.1q +| ... | tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via +| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M +| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores +| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to +| ... | io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 +| ... | Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +# Socket names +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${sock1}= | /tmp/sock-1-${bd_id1} +| ${sock2}= | /tmp/sock-1-${bd_id2} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domains with Vhost-User and VLAN in a 3-node circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid} +| | ... | ${tag_rewrite} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot new file mode 100644 index 0000000000..ea1deb9dfe --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot @@ -0,0 +1,207 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | DOT1Q | L2XCFWD | BASE | VHOST | 1VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2XC test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q +| ... | tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. Qemu Guest is connected to VPP via +| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M +| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores +| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to +| ... | io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 +| ... | Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +# Socket names +| ${sock1}= | /tmp/sock-1 +| ${sock2}= | /tmp/sock-2 +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 xconnect with Vhost-User and VLAN in 3-node circular topology +| | ... | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for dot1q-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot new file mode 100644 index 0000000000..97734b128d --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot @@ -0,0 +1,207 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | VHOST | 1VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2BD test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via +| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M +| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores +| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to +| ... | io, rxd/txd=1024, burst=64. Scheduler policy is set to SCHED_RR with +| ... | priority 1 for all Qemu CPUs. DUT1, DUT2 are tested with 2p10GE NIC X520 +| ... | Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${sock1}= | /tmp/sock-1-${bd_id1} +| ${sock2}= | /tmp/sock-1-${bd_id2} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr.robot new file mode 100644 index 0000000000..ba8e13ad7d --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr.robot @@ -0,0 +1,208 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | VHOST | 1VM | VHOST_256 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2BD test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via +| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M +| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores +| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to +| ... | io, rxd/txd=256, burst=64. Scheduler policy is set to SCHED_RR with +| ... | priority 1 for all Qemu CPUs. DUT1, DUT2 are tested with 2p10GE NIC X520 +| ... | Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${sock1}= | /tmp/sock-1-${bd_id1} +| ${sock2}= | /tmp/sock-1-${bd_id2} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${perf_qemu_qsz} | 256 +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-ethip4-ip4base-eth-2vhostvr256-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.robot new file mode 100644 index 0000000000..03bb85d6a3 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.robot @@ -0,0 +1,197 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | VHOST | 2VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2BD test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domains and MAC learning enabled. Qemu Guests are connected to VPP via +| ... | vhost-user interfaces. Guests are running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and +| ... | 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), +| ... | 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is +| ... | set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC +| ... | X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${vm_cpus}= | ${5} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domains with Vhost-User for '2' VMs in 3-node circular topology +| | And Configure '2' guest VMs with dpdk-testpmd connected via vhost-user in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot new file mode 100644 index 0000000000..93dddfeb96 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr.robot @@ -0,0 +1,204 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | VHOST | 1VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2XC test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. 802.1q +| ... | tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. Qemu Guest is connected to VPP via vhost-user interfaces. +| ... | Guest is running DPDK testpmd interconnecting vhost-user interfaces +| ... | using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using +| ... | socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores +| ... | dedicated for io), forwarding mode is set to io, rxd/txd=1024, +| ... | burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${sock1}= | /tmp/sock-1-1 +| ${sock2}= | /tmp/sock-1-2 +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 xconnect with Vhost-User in 3-node circular topology +| | ... | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-2vhostvr256-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-2vhostvr256-1vm-mrr.robot new file mode 100644 index 0000000000..3db18fd9d3 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-2vhostvr256-1vm-mrr.robot @@ -0,0 +1,205 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | VHOST | 1VM | VHOST_256 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2XC test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. 802.1q +| ... | tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. Qemu Guest is connected to VPP via vhost-user interfaces. +| ... | Guest is running DPDK testpmd interconnecting vhost-user interfaces +| ... | using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using +| ... | socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores +| ... | dedicated for io), forwarding mode is set to io, rxd/txd=256, +| ... | burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${sock1}= | /tmp/sock-1-1 +| ${sock2}= | /tmp/sock-1-2 +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${perf_qemu_qsz} | 256 +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 xconnect with Vhost-User in 3-node circular topology +| | ... | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-eth-l2xcbase-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr.robot new file mode 100644 index 0000000000..0417b1f65a --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr.robot @@ -0,0 +1,197 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | VHOST | 2VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2XC test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. 802.1q +| ... | tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connects. Qemu Guests are connected to VPP via vhost-user interfaces. +| ... | Guests are running DPDK testpmd interconnecting vhost-user interfaces +| ... | using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is +| ... | using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 +| ... | cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, +| ... | burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +#CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${vm_cpus}= | ${5} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 xconnect with Vhost-User for '2' in 3-node circular topology +| | And Configure '2' guest VMs with dpdk-testpmd connected via vhost-user in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2xcbase-eth-4vhostvr1024-2vm-ndrdisc +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr.robot new file mode 100644 index 0000000000..29925d84e3 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr.robot @@ -0,0 +1,209 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | BASE | VHOST | 1VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results IPv4 test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 +| ... | routing and two static IPv4 /24 route entries. Qemu Guest is connected +| ... | to VPP via vhost-user interfaces. Guest is running DPDK testpmd +| ... | interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 +| ... | and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), +| ... | 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is +| ... | set to mac, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE +| ... | NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${sock1}= | /tmp/sock-1 +| ${sock2}= | /tmp/sock-2 +# FIB tables +| ${fib_table_1}= | 100 +| ${fib_table_2}= | 101 +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src253 + +*** Keywords *** +| Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv4 forwarding with vhost in 3-node circular topology +| | ... | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd-mac connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 | ${dut1_vif1_mac} +| | ... | ${dut1_vif2_mac} +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd-mac connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 | ${dut2_vif1_mac} +| | ... | ${dut2_vif2_mac} +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-2vhostvr256-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-2vhostvr256-1vm-mrr.robot new file mode 100644 index 0000000000..bc8dbca328 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-2vhostvr256-1vm-mrr.robot @@ -0,0 +1,210 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | BASE | VHOST | 1VM | VHOST_256 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results IPv4 test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 +| ... | routing and two static IPv4 /24 route entries. Qemu Guest is connected +| ... | to VPP via vhost-user interfaces. Guest is running DPDK testpmd +| ... | interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 +| ... | and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), +| ... | 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is +| ... | set to mac, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE +| ... | NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${sock1}= | /tmp/sock-1-1 +| ${sock2}= | /tmp/sock-1-2 +# FIB tables +| ${fib_table_1}= | 100 +| ${fib_table_2}= | 101 +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src253 + +*** Keywords *** +| Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${perf_qemu_qsz} | 256 +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv4 forwarding with vhost in 3-node circular topology +| | ... | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd-mac connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 | ${dut1_vif1_mac} +| | ... | ${dut1_vif2_mac} +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd-mac connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 | ${dut2_vif1_mac} +| | ... | ${dut2_vif2_mac} +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-ethip4-ip4base-eth-2vhostvr256-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-ethip4-ip4base-eth-2vhostvr256-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IP4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for eth-ip4base-eth-2vhostvr256-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr.robot new file mode 100644 index 0000000000..61f912b712 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr.robot @@ -0,0 +1,203 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | BASE | VHOST | 2VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results IPv4 test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 +| ... | routing and two static IPv4 /24 route entries. Qemu Guests are connected +| ... | to VPP via vhost-user interfaces. Guests are running DPDK testpmd +| ... | interconnectingvhost-user interfaces using 5 cores pinned to cpus 6-10 +| ... | and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M +| ... | hugepages), 5 cores (1 main core and 4 cores dedicated for io), +| ... | forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are +| ... | tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${sock1}= | /tmp/sock-1 +| ${sock2}= | /tmp/sock-2 +# FIB tables +| ${fib_table_1}= | 100 +| ${fib_table_2}= | 101 +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${vm_cpus}= | ${5} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src253 + +*** Keywords *** +| Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv4 forwarding with vhost for '2' VMs in 3-node circular topology +| | And Configure '2' guest VMs with dpdk-testpmd-mac connected via vhost-user in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4-ip4base-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot new file mode 100644 index 0000000000..5869d1ccb6 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot @@ -0,0 +1,212 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY +| ... | VHOST | 1VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2BD test cases with VXLANoIPv4 +| ... | and vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via +| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M +| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores +| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to +| ... | io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 +| ... | Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC7348. + +*** Variables *** +# Socket names +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${sock1}= | /tmp/sock-1-${bd_id1} +| ${sock2}= | /tmp/sock-1-${bd_id2} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${vxlan_overhead} | ${50} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize} + ${vxlan_overhead} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domains with Vhost-User and VXLANoIPv4 in 3-node circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/40ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/40ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot new file mode 100644 index 0000000000..4f10eb2fd2 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/40ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot @@ -0,0 +1,206 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X710 | ETH | L2BDMACLRN | BASE | VHOST | 1VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-XL710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2BD test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. Qemu Guests are connected to VPP via +| ... | vhost-user interfaces. Guests are running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M +| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores +| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to +| ... | io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 +| ... | by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${sock1}= | /tmp/sock-1-${bd_id1} +| ${sock2}= | /tmp/sock-1-${bd_id2} +# X710 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/40ge2p1xl710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/40ge2p1xl710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot new file mode 100644 index 0000000000..5ad857ae23 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/40ge2p1xl710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot @@ -0,0 +1,210 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-XL710 | ETH | L2BDMACLRN | BASE | VHOST | 1VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-XL710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2BD test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. Qemu Guests are connected to VPP via +| ... | vhost-user interfaces. Guests are running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M +| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores +| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to +| ... | io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p40GE NIC XL710 +| ... | by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# Socket names +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${sock1}= | /tmp/sock-1-${bd_id1} +| ${sock2}= | /tmp/sock-1-${bd_id2} +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${get_framesize} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} +| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1 +| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1} +| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user +| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1 +| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2} +| | Run Keyword Unless | ${qemu_built} | Set Suite Variable | ${qemu_built} +| | ... | ${True} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 diff --git a/tests/vpp/perf/vm_vhost/40ge2p1xl710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.robot b/tests/vpp/perf/vm_vhost/40ge2p1xl710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.robot new file mode 100644 index 0000000000..6cc2659fe5 --- /dev/null +++ b/tests/vpp/perf/vm_vhost/40ge2p1xl710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.robot @@ -0,0 +1,201 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.QemuUtils +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-XL710 | ETH | L2BDMACLRN | BASE | VHOST | 2VM | VHOST_1024 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-XL710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance mrr test with vhost and VM with dpdk-testpmd +| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs} +| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs} +| ... +| Documentation | *Raw results L2BD test cases with vhost* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. Qemu Guests are connected to VPP via +| ... | vhost-user interfaces. Guests are running DPDK testpmd interconnecting +| ... | vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M +| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores +| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to +| ... | io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p40GE NIC XL710 +| ... | by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${vm_cpus}= | ${5} +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with ${wt} thread, ${wt} phy\ +| | ... | core, ${rxq} receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${get_framesize} +| | ${max_rate}= | Set Variable If +| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate} +| | ${dut1_vm_refs}= | Create Dictionary +| | ${dut2_vm_refs}= | Create Dictionary +| | Set Test Variable | ${dut1_vm_refs} +| | Set Test Variable | ${dut2_vm_refs} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domains with Vhost-User for '2' VMs in 3-node circular topology +| | And Configure '2' guest VMs with dpdk-testpmd connected via vhost-user in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-IMIX-1t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy\ +| | ... | core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=2 | rxq=1 + +| tc06-IMIX-2t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy\ +| | ... | cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${64} | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=${1518} | wt=4 | rxq=2 + +| tc09-IMIX-4t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy\ +| | ... | cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 |