diff options
author | Mauro Sardara <msardara@cisco.com> | 2019-09-23 19:34:23 +0200 |
---|---|---|
committer | Mauro Sardara <msardara@cisco.com> | 2019-09-24 11:14:16 +0200 |
commit | a0da41b243661a039481d2c254d7db8f55f18d2b (patch) | |
tree | e06e06a609588ceb8f5e293abc02a4a02da39d4d /utils/extras/README.md | |
parent | d6bd901a818e10f2e224bfaaaf20b39b60b6009f (diff) |
[HICN-279] Added libmemif packaging.
Change-Id: Ie8662059163b7a01211bb18fb8f6b77bbbc07279
Signed-off-by: Mauro Sardara <msardara@cisco.com>
Diffstat (limited to 'utils/extras/README.md')
-rw-r--r-- | utils/extras/README.md | 49 |
1 files changed, 0 insertions, 49 deletions
diff --git a/utils/extras/README.md b/utils/extras/README.md deleted file mode 100644 index 40363ef18..000000000 --- a/utils/extras/README.md +++ /dev/null @@ -1,49 +0,0 @@ -# Configure VPP and FRRouting for OSPF6 -This document describes how to configure the VPP with hicn_router plugin and FRR to enable the OSPF protocol. The VPP and FRR -are configured in a docker file. - -## DPDK configuration on host machine: - -- Install and configure dpdk - - make install T=x86_64-native-linux-gcc && cd x86_64-native-linux-gcc && sudo make install - - modprobe uio - - modprobe uio_pci_generic - - dpdk-devbind --status - - the PCIe number of the desired device can be observed ("xxx") - - sudo dpdk-devbind -b uio_pci_generic "xxx" -## VPP configuration: - -- Run and configure the VPP (hICN router plugin is required to be installed in VPP) - - set int state TenGigabitEtherneta/0/0 up - - set int ip address TenGigabitEtherneta/0/0 a001::1/24 - - create loopback interface - - set interface state loop0 up - - set interface ip address loop0 b001::1/128 - - enable tap-inject # This creates the taps by router plugin - - show tap-inject # This shows the created taps - - ip mroute add ff02::/64 via local Forward # ff02:: is multicast ip address - - ip mroute add ff02::/64 via TenGigabitEtherneta/0/0 Accept - - ip mroute add ff02::/64 via loop0 Accept - -- Setup the tap interface - - ip addr add a001::1/24 dev vpp0 - - ip addr add b001::1/128 dev vpp1 - - ip link set dev vpp0 up - - ip link set dev vpp1 up - -## FRR configuration: - -- Run and configure FRRouting (ospf) - - /usr/lib/frr/frrinit.sh start & - - vtysh - - configure terminal - - router ospf6 - - area 0.0.0.0 range a001::1/24 - - area 0.0.0.0 range b001::1/128 - - interface vpp0 area 0.0.0.0 - - interface vpp1 area 0.0.0.0 - - end - - wr - - add "no ipv6 nd suppress-ra" to the first configurtion part of the /etc/frr/frr.conf -After the following configuration, the traffic over tap interface can be observered through "tcpdump- i vpp1". -The neighborhood and route can be seen by the "show ipv6 ospf6 neighbor/route". |