aboutsummaryrefslogtreecommitdiffstats
path: root/utils/extras
diff options
context:
space:
mode:
authormhemmatp <mhemmatp@cisco.com>2019-09-17 05:50:58 -0700
committermhemmatp <mhemmatp@cisco.com>2019-09-17 06:32:03 -0700
commitd6bd901a818e10f2e224bfaaaf20b39b60b6009f (patch)
tree9f16fa397dd2bd7c2ff1eb31b7bf220258bd2311 /utils/extras
parent288f00b322b6573c637e5567c528a4ff9ab5bfba (diff)
[ HICN-277] Add README to router plugin
Signed-off-by: mhemmatp <mhemmatp@cisco.com> Change-Id: I838da25116f5fc4a674957510699bf5a00c99cad
Diffstat (limited to 'utils/extras')
-rw-r--r--utils/extras/README.md49
1 files changed, 49 insertions, 0 deletions
diff --git a/utils/extras/README.md b/utils/extras/README.md
new file mode 100644
index 000000000..40363ef18
--- /dev/null
+++ b/utils/extras/README.md
@@ -0,0 +1,49 @@
+# Configure VPP and FRRouting for OSPF6
+This document describes how to configure the VPP with hicn_router plugin and FRR to enable the OSPF protocol. The VPP and FRR
+are configured in a docker file.
+
+## DPDK configuration on host machine:
+
+- Install and configure dpdk
+ - make install T=x86_64-native-linux-gcc && cd x86_64-native-linux-gcc && sudo make install
+ - modprobe uio
+ - modprobe uio_pci_generic
+ - dpdk-devbind --status
+ - the PCIe number of the desired device can be observed ("xxx")
+ - sudo dpdk-devbind -b uio_pci_generic "xxx"
+## VPP configuration:
+
+- Run and configure the VPP (hICN router plugin is required to be installed in VPP)
+ - set int state TenGigabitEtherneta/0/0 up
+ - set int ip address TenGigabitEtherneta/0/0 a001::1/24
+ - create loopback interface
+ - set interface state loop0 up
+ - set interface ip address loop0 b001::1/128
+ - enable tap-inject # This creates the taps by router plugin
+ - show tap-inject # This shows the created taps
+ - ip mroute add ff02::/64 via local Forward # ff02:: is multicast ip address
+ - ip mroute add ff02::/64 via TenGigabitEtherneta/0/0 Accept
+ - ip mroute add ff02::/64 via loop0 Accept
+
+- Setup the tap interface
+ - ip addr add a001::1/24 dev vpp0
+ - ip addr add b001::1/128 dev vpp1
+ - ip link set dev vpp0 up
+ - ip link set dev vpp1 up
+
+## FRR configuration:
+
+- Run and configure FRRouting (ospf)
+ - /usr/lib/frr/frrinit.sh start &
+ - vtysh
+ - configure terminal
+ - router ospf6
+ - area 0.0.0.0 range a001::1/24
+ - area 0.0.0.0 range b001::1/128
+ - interface vpp0 area 0.0.0.0
+ - interface vpp1 area 0.0.0.0
+ - end
+ - wr
+ - add "no ipv6 nd suppress-ra" to the first configurtion part of the /etc/frr/frr.conf
+After the following configuration, the traffic over tap interface can be observered through "tcpdump- i vpp1".
+The neighborhood and route can be seen by the "show ipv6 ospf6 neighbor/route".